Emriver Em2 Скачать руководство пользователя | Manualshive

Страница: 17 / 26

background image

Assembly and Operation

© 2012 Little River Research & Design; updated July 2018

17

STEP 11 - Power the pump

Attach the brick power supply to the leg of the shorter support using the mushroom fasteners

on the support and the brick power supply. Wrap the Velcro® strap around the support leg and

the brick power supply to fasten securely. See Figure 17

.

Figure 17. Attach the brick power supply to the leg of the downstream

support.

Connect the power cord to the Ground Fault Circuit

Interrupter (GFCI) (US users only). If you are using an

extension cord, connect the extension cord to the

GFCI. Do not plug the model's power cord directly

into a wall outlet.

Always use the GFCI.

If the red indicator light on the GFCI is on, it is ready

for use and the model should be powered. If the red

indicator light is off, press the red “Reset” button.

Figure 18. Always connect the power

cord to the GFCI. Never plug the

model's power supply directly into a

wall outlet.

«
...
15
16
17
18
19
...
»

Содержание Em2



























Отзывы:

Нет отзывов

Похожие инструкции для Em2

Бренд: Uncle Milton Страницы: 3

Бренд: CruizCore Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды