background image

31792-4-1115

Page 42

AUTOMATIC HUMIDIFIER OPERATION

The Mantis Power-Vent High-Efficiency Fireplace has an automat

-

ic humidifier designed into the fireplace. As the fireplace operates, 

condensate is created and is collected in a tank inside the fire

-

place. The condensate pump will take the collected condensate  

and pump it to a stainless steel tray where it evaporates into the 

airstream, adding humidity to the heated space. 

Note:

 When the automatic humidifier is engaged and is transfer

-

ring  the  condensate,  there  may  be  a  noticeable  hissing  sound. 

This is normal, and the sound should persist for less than 30 sec

-

onds. 
The amount of condensate created will vary based on several 

factors including but not limited to location of fireplace, air tem

-

perature, length of venting, and whether the vent pipe is horizontal 

or vertical. The humidifier will operate intermittently while the fire

-

place is operating.
While the condensate pump is transferring the condensate from 

the  tank  to  the  tray,  the  “AUX”  symbol  will  display  during  pump 

 

operation. See Page 32, Figure 48. Once the condensate is trans

-

ferred, the symbol will turn off.

Figure 63

MAINTENANCE & SERVICE

The Mantis should be inspected and serviced annually by a quali-

fied service person. This will ensure that the appliance is operating 

safely  and  efficiently.  Should  you  suspect  any  abnormal  opera

-

tion, contact a service person that has been trained to service this 

product. 

Cleaning the Glass Door

After the initial paint curing, a slight film may form on the glass. It is 

recommended to clean the glass with gas fireplace glass cleaner.

The glass will need to be cleaned periodically during the year. Use 

care when removing and cleaning the glass. In the event the glass 

needs replaced, contact a qualified service person. Only glass ap

-

proved by Empire Comfort Systems Inc. may be used, any substi

-

tute glasses will void the warranty. 

CAUTION

Do not attempt to clean the glass when it is hot. Do not 

strike or hit the glass. 

WARNING

Do not operate this appliance without the glass door 

in place. Do not operate if the glass front is broken or  

damaged. Do not use the glass door if the gasket is missing 

or is damaged. 

CAUTION

Be certain the glass is cool before handling.

Removing the Glass Door

1.  Remove the lower louvered panel by lifting up then pulling 

out.

2.  Release the two hinge clips on underside of firebox.

3.  Angle  the  bottom  of  glass  assembly  approximately  60  de

-

grees out from firebox. Gently pull glass assembly away from 

firebox. Do not damage or remove the gasket from the door. 

Resetting the Fireplace

WARNING

Potential  risk  of  fire,  electric  shock,  and  personal  injury. 

Take precautions to reduce such risks

CAUTION

Label all wires prior to disconnection when servicing  

controls. Wiring errors can cause improper and dangerous 

operation. Verify proper operation after servicing.

To reset the fireplace, press the mode selection button on the dis

-

play panel repeatedly until the fireplace cycles through the “OFF” 

setting once. If the error has been cleared, the fireplace will oper

-

ate normally. If the error is still present, consult a qualified service 

technician.

Cleaning the Porcelain Liners

Over  time  a  film  may  form  on  the  porcelain  liners.  It  is  recom

-

mended to clean the liners with gas fireplace glass cleaner. 

The liners will need to be cleaned periodically during the year. The 

glass door will need to be removed to clean the liners. Use care 

when removing the glass. In the event the liners need to be re-

placed, contact a qualified service person. Only liners supplied by 

Empire Comfort Systems may be used. Any substitute will void the 

warranty.

Содержание Mantis FG28BM-1





















































Отзывы: