Empire Comfort Systems P)-4 Скачать руководство пользователя

Страница: 47 / 80

28649-2-0811

Page 47

STANDING PILOT OPERATING INSTRUCTIONS

Remote/Off/On Switch

The fireplace is equipped with a Remote/OFF/ON switch. A wire

harness is attached to the Remote/OFF/ON switch. The red, black

and green (wires) female push-ons attach to the Remote/OFF/

ON switch. At the opposite end of the wire harness, the black and

green (wires) female push-ons attach to the gas valve. An additional

green wire and the red wire, which are stripped and bare, will at-

tach to one of the accessories that can be purchased for use with

your fireplace.

Operation of REMOTE/OFF/ON Switch with no Accessories

To ignite main burner, turn the control knob on the gas valve from the

PILOT position to the ON position. Turn the Remote/OFF/ON switch

from the OFF position to the ON position. The additional green wire

and red wire, which are stripped and bare are not used.

Wall Switch, FWS-1

Connect the green and red, stripped and bare, wires on the REMOTE/

OFF/ON switch wire harness to the wall switch. Turn the REMOTE/

OFF/ON switch to the Remote position. Pivot the rocker switch on

the FWS-1 to the ON position.

Wall Thermostats (optional)

TRW - Wireless for Millivolt models

TMV - Reed switch for Millivolt models

Battery Operated Remote Controls, FRBC, FBRTC, and TRW

Connect the green and red, stripped and bare, wires on the

REMOTE/OFF/ON switch wire harness to the remote receiver that

is a component in the remote kit. Turn the REMOTE/OFF/ON switch

to the remote position. Follow instructions included with the remote

to complete installation.

Note: If batteries fail in the remote, and immediate heat is desired,

turn the REMOTE/OFF/ON switch from the REMOTE position to

the ON position.

Electric (120 volt) Operated Remote Control, FREC

Connect the green and red, stripped and bare, wires on the REMOTE/

OFF/ON switch wire harness to the wires on remote receiver that

is a component in the FREC. Turn the REMOTE/OFF/ON switch to

the REMOTE position. Follow instructions in the FREC to complete

installation.

NOTE:

If electric (120 colt) fails in FREC, and immediate heat is

desired, turn the REMOTE/OFF/ON switch from the REMOTE

position to the ON position.

Installation of Remote Receiver

Place remote receiver on the floor of fireplace behind the louver as

far forward as possible.

Attention:

The velcro loop and hook are not necessary in this

installation but can be used to secure remote receiver.
Refer to remote control installation and operating instructions for

more details on remote control.

Millivolt Control

The valve regulator controls the burner pressure which should be

checked at the pressure test point. Turn captured screw counter

clockwise 2 or 3 turns and then place tubing to pressure gauge over

test point (Use test point “A” closest to control knob). After taking

pressure reading, be sure and turn captured screw clockwise firmly

to re-seal. Do not over torque. Check for gas leaks.
Millivolt thermopile is self generating. Gas valve does not require

24 volts or 110 volts.

Check System Operation

Millivolt system and all individual components may be checked with

a millivolt meter 0-1000 MV range.

It is important to use wire of a gauge proper for the length of the

wire:

Recommended Wire Gauges

Maximum Length

Wire Gauge

1' to 10'

10' to 25'

25' to 35'

OPERATING INSTRUCTIONS (continued)

Содержание P)-4

















































































Результаты поиска

Содержание P)-4

Отзывы:

Похожие инструкции для P)-4

Бренды по названию

Популярные бренды

Empire Comfort Systems P)-4, Инструкция по установке и руководство пользователя

Результаты поиска

Содержание P)-4

Отзывы:

Похожие инструкции для P)-4

Бренды по названию

Популярные бренды