manualshive.com logo in svg

Empire Comfort Systems MILLIVOLT STANDING PILOT DVX36FP31L-4, Инструкция по установке и руководство пользователя, Страница: 61 / 96

Поделиться
Скачать
Empire Comfort Systems MILLIVOLT STANDING PILOT DVX36FP31L-4 Скачать руководство пользователя страница 61

39357-0-1018

Page 61

STANDING PILOT OPERATING INSTRUCTIONS 

Remote/Off/On Switch

The fireplace is equipped with a Remote/OFF/ON switch. A wire 

harness is attached to the Remote/OFF/ON switch. The red, black 

and green (wires) female push-ons attach to the Remote/OFF/ON 

switch. At the opposite end of the wire harness, the black and green 

(wires) female push-ons attach to the gas valve. An additional green 

wire and the red wire, which are stripped and bare, will attach to one 

of the accessories that can be purchased for use with your fireplace. 

Operation of REMOTE/OFF/ON Switch with no Accessories

 

To ignite main burner, turn the control knob on the gas valve from 

the PILOT position to the ON position. Turn the Remote/OFF/ON 

switch from the OFF position to the ON position. The additional 

green wire and red wire, which are stripped and bare are not used.

Wall Switch, FWS-1

Connect the green and red, stripped and bare, wires on the REMOTE/

OFF/ON switch wire harness to the wall switch using wire nuts. 

Turn the REMOTE/OFF/ON switch to the Remote position. Pivot 

the rocker switch on the FWS-1 to the ON position. 

Wall Thermostats (optional)

TRW - Wireless for Millivolt models

TMV - Reed switch for Millivolt models

Battery Operated Remote Controls, FRBC, FRBTC, and TRW

 

Connect the green and red, stripped and bare, wires on the 

REMOTE/OFF/ON switch wire harness to the remote receiver that 

is a component in the remote kit using wire nuts. Turn the REMOTE/

OFF/ON switch to the remote position. Follow instructions included 

with the remote to complete installation. 

Note: If batteries fail in the remote, and immediate heat is desired, 

turn the REMOTE/OFF/ON switch from the REMOTE position to 

the ON position. 

Electric (120 volt) Operated Remote Control, FREC

Connect the green and red, stripped and bare, wires on the REMOTE/

OFF/ON switch wire harness to the wires on remote receiver that 

is a component in the FREC using wire nuts. Turn the REMOTE/

OFF/ON switch to the REMOTE position. Follow instructions in the 

FREC to complete installation.

NOTE:

 If electric (120 Volt) fails in FREC, and immediate heat 

is desired, turn the REMOTE/OFF/ON switch from the REMOTE 

position to the ON position.

Installation of Remote Receiver 

Place remote receiver on the floor of fireplace behind the louver as 

far forward as possible.

Attention: 

The velcro loop and hook are not necessary in this 

installation but can be used to secure remote receiver.
Refer to remote control installation and operating instructions for 

more details on remote control.

Millivolt Control

The valve regulator controls the burner pressure which should be 

checked at the pressure test point. Turn captured screw counter 

clockwise 2 or 3 turns and then place tubing to pressure gauge over 

test point (Use test point “A” closest to control knob). After taking 

pressure reading, be sure and turn captured screw clockwise firmly 

to re-seal. Do not over torque. Check for gas leaks.
Millivolt thermopile is self generating. Gas valve does not require 

24 volts or 110 volts. 

Check System Operation

Millivolt system and all individual components may be checked with 

a millivolt meter 0-1000 MV range.

It is important to use wire of a gauge proper for the length of the wire:

Recommended Wire Gauges

Maximum Length

Wire Gauge

1' to 10'

18

10' to 25'

16

25' to 35'

14

MILLIVOLT SYSTEM OPERATING INSTRUCTIONS (CONT'D)

Содержание MILLIVOLT STANDING PILOT DVX36FP31L-4

































































































Отзывы:

Нет отзывов