background image

Page 12

R-3122

FOR YOUR SAFETY READ BEFORE OPERATING

WARNING:  If you do not follow these instructions exactly, a fire or explosion may result

causing property damage, personal injury or loss of life.

A. This appliance is equipped with an ignition device

which automatically lights the pilot.

Do not try to light the pilot by hand.

B. BEFORE OPERATING  smell all around the appliance

area for gas.  Be sure to smell next to the floor because
some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.
• Do not touch any electrical switch;

do not use any phone in your building.

• Immediately call your gas supplier from a neigh-

bor's phone.  Follow the gas supplier's instructions.

• If you cannot reach your gas supplier, call the fire

department.

C. Use only your hand to slide the gas control knob.

Never use tools. Force or attempted repair may
result in a fire or explosion.

D. Do not use this appliance if any part has been under

water.  Immediately call a qualified service techni-
cian to inspect the appliance and to replace any part
of the control system and any gas control which has
been under water.

1. STOP!   Read the safety information above.

2. Set the thermostat to lowest setting.

3. Turn off all electric power to the appliance.

4. This appliance is equipped with an ignition device

which automatically lights the pilot.  Do not try to
light the pilot by hand.

O

N

OF

F

IGNITOR

CONTROL

GAS FLOW

GAS VALVE SHOWN IN OFF POSITION

HONEYWELL IP SMART VALVE

5. Remove front panel door.

6. Slide  gas control switch to "OFF."

7. Wait ten (10) minutes   to clear out any gas.  Then

smell for gas, including near the floor.  If you smell
gas, STOP! Follow "B" in the safety information
above.  If you don't smell gas, go to the next step.

8. Slide gas control switch to "ON".

9. Replace front panel  door.

10. Turn on all electric power to the appliance.

11. Set thermostat to desired setting.

12. If the appliance will not operate, follow the instruc-

tions "TO TURN OFF GAS TO APPLIANCE" and
call your service technician or gas supplier.

OPERATING INSTRUCTIONS

TO TURN OFF GAS TO APPLIANCE

1. Set the thermostat to lowest setting.

2. Turn off all electric power to the appliance if service

is to be performed.

3. Remove front panel door.

4. Slide gas control switch to "OFF."

5. Replace front panel door.

INTERMITTENT PILOT (IP) MODEL

Содержание DVC-35IP

















Отзывы: