manualshive.com logo in svg
background image

R-3122

 Page 1

INSTALLATION  INSTRUCTIONS

AND

OWNER'S  MANUAL

FAN TYPE

DIRECT  VENT

WALL  FURNACE

MODEL

DVC-35-1SPP

DVC-35-1IP

EFFECTIVE  DATE

AUGUST, 2000

WARNING:  If the information in this
manual is not followed exactly, a fire or
explosion may result causing property
damage, personal injury or loss of life.

 — Do not store or use gasoline or other

flammable vapors and liquids in the vi-
cinity of this or any other appliance.

  — WHAT TO DO IF YOU SMELL GAS

Do not try to light any appliance.

Do not touch any electrical switch; do
not use any phone in your building.

Immediately call your gas supplier
from a neighbor's phone.  Follow the
gas supplier's instructions.

If you cannot reach your gas supplier,
call the fire department.

 — Installation and service must be per-

formed by a qualified installer, service
agency or the gas supplier.

WARNING: If not installed, operated and
maintained in accordance with the manu-
facturer's instructions, this product could
expose you to substances in fuel or from fuel
combustion which can cause death or seri-
ous illness.

This appliance may be installed in an after-
market permanently located, manufactured
(mobile) home, where not prohibited by state
or local codes.

This appliance is only for use with the type of
gas indicated on the rating plate. This appli-
ance is not convertible for use with other
gases, unless a certified kit is used.

Содержание DVC-35IP

















Отзывы: