manualshive.com logo in svg
background image

IMPORTANT! Read these instructions carefully 

before installing or operating this gas appliance. 

These instructions should be left with the 

homeowner for future reference.

RADIANT VENTED BURNER

REQUIRES VENTED LOG SET 

FOR INSTALLATION IN 

SOLID-FUEL BURNING FIREPLACES

VARIABLE 

REMOTE MODELS

BFE(2124,30)MTN

GAS-FIRED

CONGRATULATIONS on the purchase of 

your new GAS BURNER! Your Decorative 

Gas Burner is designed and intended for 

installation in an approved, existing, fully 

vented, wood-burning fireplace, with a gas 

hook-up. 

This appliance must be installed only in a solid-

fuel burning fireplace with a working flue and 

construction of noncombustible materials.

The vent damper must have a damper clamp 

attached to it to keep the damper from 

accidentally closing during operation.

This unit is NOT for use with solid fuel. Sol-

id fuels shall NOT be burned in a fireplace 

where a decorative appliance is installed.

DANGER

If not installed, operated and maintained 

in accordance with the manufacturer’s 

instructions, this product could expose you 

to substances in fuel or from fuel combustion 

which can cause death or serious illness.

WARNING

FIRE OR EXPLOSION HAZARD

If the information in this manual is not 

followed exactly, a fire or explosion may 

result causing property damage, personal 

injury or loss of life.

—  Do not store or use gasoline or other 

flammable vapors and liquids in the 

vicinity of this or any other appliance.

—  WHAT TO DO IF YOU SMELL GAS

•  Do not try to light any appliance.

•  Do not touch any electrical switch; do 

not use any phone in your building.

•  Leave the building immediately.

•  Immediately call your gas supplier 

from a neighbor’s phone. Follow the 

gas supplier’s instructions.

•  If you cannot reach your gas supplier, 

call the fire department.

—  Installation and service must be 

performed by a qualified installer, 

service agency or the gas supplier.

INSTALLER: 

Leave this manual with the appliance.

CONSUMER: 

Retain this manual for future reference.

INSTALLATION INSTRUCTIONS

AND OWNER’S MANUAL

Содержание BFE2124MTN





























Отзывы: