EMKO ESM-9910 Скачать руководство пользователя страница 32

Страница: 32 / 46

OUT

SET

PROG

SET

If Enter button is
pressed, next
parameter is shown.

OUT

SET

PROG

SET

Parameter value can be
observed by pressing
increment button.

Parameter can be
changed with increment
and decrement buttons.

OUT

SET

PROG

SET

OUT

SET

PROG

SET

OUT

SET

PROG

SET

OUT

SET

PROG

SET

Press Enter

button for

saving

parameter

value.

Press SET

button to exit

from

programming

mode.

Press SET button to

turn to the

programming screen

without saving the

parameter.

Press SET button to turn to

the programming screen

without saving the

parameter.

Programming Mode
Accessing Password

Programming Mode
Accessing Password
Value

Programming
Mode
Accessing
Password
Value

It turns to
beginning of
the
programming
mode

Hysteresis
Parameter

Press SET button to

exit from programming

section

If Enter button is
pressed, next parameter
is shown.

Programming Screen

If no operation is done in programming or Set value mode for 20 seconds, device
turns to main operation screen automatically.

Continue to press SET2/Enter

button for accessing to the

parameters.

Main Operation Screen

In programming screen,

Press SET1 button to exit

from programming mode and

turn to the main operation

screen.

Содержание ESM-9910















































Результаты поиска

Содержание ESM-9910

Отзывы:

Похожие инструкции для ESM-9910

Бренды по названию

Популярные бренды

EMKO ESM-9910, Инструкция по эксплуатации

Результаты поиска

Содержание ESM-9910

Отзывы:

Похожие инструкции для ESM-9910

Бренды по названию

Популярные бренды