Emfit D-1090-2G Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 15

Emfit D-1090-2G Скачать руководство пользователя страница 7

7

8.

INSTALLING BATTERIES AND BATTERY CONSUMPTION

Product operates with 2 pcs AA size 1.5 V batteries. Install and remove the batteries as follows:

Estimated battery life is 6 months, when using high quality alkaline batteries, with 2800 mAh capacity (2pcs). Estimation is
based on measured battery consumption in various conditions and then a calculation where device is on 50% of time (shut down
50% of time) and of that 50% of time there is someone in bed 75% of that time, there are two notifications per day and sound
notification is on 30 seconds each time.

WHEN THE BATTERIES ARE GETTING LOW, THE RED LED BEGINS TO FLASH SLOWLY, A “BEEP” SOUND WILL BE HEARD
AFTER EVERY 1,5 HOURS AND THE DRY-CONTACT OUTPUT GIVES LOW BATTERY NOTIFICATION AFTER EVERY 3 HOURS.

9.

ABOUT THE OPTIONAL 5V AC ADAPTER

For preparing the optional power supply for use, do the following:

THE EMFIT EPILEPTIC TONIC-CLONIC SEIZURE ALARM IS DESIGNED AND TESTED TO BE USED ONLY WITH GLOBTEK
INC. POWER SUPPLY MODEL: NO GTM41060-1505 AND P/N:WR9QA3000LCP-N-MNK. ANY OTHER TYPE OF AC ADAPTER
MAY AFFECT THE PRODUCT’S SAFETY.

The power supply is equipped with a blue indicator light; when the light is on the power supply is in use. If the light is off and
the power supply is connected to the mains outlet, the power supply is probably damaged and should be replaced.

WHEN THE AC ADAPTER IS CONNECTED TO THE POWER INPUT, THE BATTERIES ARE ELECTRICALLY DISCONNECTED.
IN CASE OF NO MAINS POWER AND AC ADAPTER CORD IS CONNECTED TO X1, THE BATTERIES INSIDE WILL NOT

OPERATE AS BACK UP POWER SUPPLY.

Open the cover by lifting from
one side

Install 2 pcs good quality alkaline
AA size 1,5 V alkaline batteries
according the polarity drawings
on the circuit board

When removing old batteries,
they are easiest to remove by
lifting from + ends

Remove the plastic cover

Pick up suitable adapter from the
included 4 pcs

Install the adapter and make
sure it stays in place

«
...
5
6
7
8
9
...
»

Содержание D-1090-2G
















Отзывы:

Нет отзывов