background image

Disconnect wires from existing
switches only. Do not attempt to
disconnect any wires not already
connected to existing switches. 

NOTE: Retrofit 3-way installations are
likely to include two traveler wires
between the two wall boxes. In new
construction, only one traveler wire is
required.

3. Before installing wall control, place wall

control in “OFF” mode by pushing
“ON/OFF” switch to the “OFF” position.

4. Install a wall control in the wall box

containing the “hot” wire first. Connect
one black wire of the wall control to the
“hot” wire. Securely connect wires with
wire connectors supplied.

5. Connect the other black wire of the wall

control to the remaining traveler wire(s)
in the wall box and secure with wire
connector supplied.

3-WAY WIRlNG DIAGRAM:
NEW CONSTRUCTION

6. Place wall control into wall box. Screw

in place and install decorator style
faceplate. 

7. Next, install the other wall control into

the wall box containing the “load” wire.
Connect one black wire of the wall
control to the traveler wire(s) already
connected to the black wire (in the
other wall box). Secure with wire
connectors supplied. 

7

STANDARD WIRING FOR EXISTING
3-WAY CONTROLS

HOT

BLK

TRAVELER WIRES

BLACK

LOAD

EXISTING
WALL  CONTROL

SW350
WALL CONTROL

BLK

BLK

BLK

BLACK

LOAD

TRAVELER WIRES

HOT

BLK

Off

On

Up

Down

Lights

Fan

Sleep

Off

On

Up

Down

Lights

Fan

Sleep

3-WAY WIRING DIAGRAM: RETROFIT

Figure 13

Do not connect any neutral (white) wire
to this control. Incorrect wiring will
damage this control.

WARNING

!

HOT

BLK

SW350
WALL 
CONTROL

BLK

TRAVELER
WIRE

BLK

BLK

LOAD
BLACK

GROUND

NEUTRAL

Off

On

Up

Down

Lights

Fan

Sleep

Off

On

Up

Down

Lights

Fan

Sleep

FAN RECEIVER LOCATED 
WITHIN CEILING CANOPY 

AMERICA’S FAN COMPANY

Figure 12

8. Connect one black wire of the wall

control to the “load” (black) wire and
secure with wire connector supplied. 

9. Place the second wall control into the

wall box. Screw in place and install
decorator style faceplate (included).
Leave switch in “OFF” mode until fan
installation is completed. 

10. Refer to fan Owner’s Manual to

complete fan installation. 

NOTE: You must perform the Code
Learning Procedure for both wall
controls to be able to operate your fan
from both wall controls.

BP7253-2  4/28/06  11:58 AM  Page 7

Содержание SR330













Отзывы: