Emerson Rosemount Xi Скачать руководство пользователя страница 38

Страница: 38 / 82

Password protection can be enabled by selecting

System Main Menu > Configure > LCD >

Enable Password

(see

Figure 4-2

The factory default upon enabling the password protection is

ROSE

, but the password can

consist of any 4 alpha/numeric characters.

If you forget the password, do one of the following:

•

In North America, call Emerson's Rosemount Customer Central at 1-800-999-9307.

•

For everywhere else, contact your nearest Emerson representative or go to

Emerson.com

Lock

icon is displayed at the top right corner of the main display when password

protection is in effect.

The password protection relocks itself after a certain number of seconds with no button
pushes (defined as

revert time

in the same

LCD setup

menu). You can also force the front

panel to be locked by selecting

System Main Menu > Log Off

. The

Log Off

selection

performs on function if the password feature is disabled.

The Rosemount Xi has a

Reset

function that reestablishes all factory default conditions,

including the password protection feature, i.e., the password protection falls back to a
disabled condition after a reset.

4.3

System parameter descriptions

Among the parameters available through the Rosemount Xi and Field Communicator
menus are a number of

system parameters

. The system parameters define variables that

configure the Rosemount Xi in the transmitter system. System parameters are described
in the following table.

Table 4-1: System parameters

CPU

Parameter name

Units

Parameter description

Version

---

Software version number for the CPU
board

Build Num

---

Software build number for the CPU
board

Comm Status

---

Communication status between the
CPU and I/O boards

Restart Cntr

---

Software restarts counter for the CPU
board

Pol Addr

---

Polling address - address used to
identify a field device; changeable by
user

Serial Number

---

I/O board serial number

Features

---

Available advanced software features
for the I/O board.
ON: feature supported.
OFF: feature not supported.

Startup and operation

Reference Manual

October 2022

00809-0100-4889

Rosemount Xi

Содержание Rosemount Xi



















































































Результаты поиска

Содержание Rosemount Xi

Отзывы:

Emerson Rosemount Xi, Справочное руководство, Страница: 38 / 82

Результаты поиска

Содержание Rosemount Xi

Отзывы: