Emerson Rosemount Xi Скачать руководство пользователя страница 27

Страница: 27 / 82

Configure

3.1

Verify installation

WARNING

ELECTRIC SHOCK

Install all protective equipment covers and safety ground leads before equipment

startup. Failure to install covers and ground leads could result in serious injury or death.

WARNING

ELECTRIC SHOCK

If external loop power is used, the power supply must be a safety extra low voltage

(SELV) type.

3.1.1

Rosemount Xi configuration

Refer to

Figure 3-1

and

Table 3-1

for the configuration of jumpers JP1 through JP8. The

jumper configuration for your I/O board depends on the system design and system
components used in your installation.

The setting of switch SW4 and the configuration of jumpers JP1 through JP8 must be
verified on the I/O board in the Rosemount Xi. All four dip switches on switch SW4 must be
set to the

Off

position, as shown.

Reference Manual

Configure

00809-0100-4889

October 2022

Emerson.com/Rosemount

Содержание Rosemount Xi



















































































Результаты поиска

Содержание Rosemount Xi

Отзывы:

Emerson Rosemount Xi, Справочное руководство, Страница: 27 / 82

Результаты поиска

Содержание Rosemount Xi

Отзывы: