Emerson Rosemount Smart Wireless THUM Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 60

background image

Reference Manual

00809-0100-4075, Rev BA

October 2010

Smart Wireless THUM Adapter

4-4

AMS Wireless Configurator

When the device has joined the network, it will appear in the Wireless
Configurator as illustrated below.

Troubleshooting

If the device is not operating properly, refer to the troubleshooting section of
the manual. The most common cause of incorrect operation is the Network ID
and Join Key. The Network ID and Join Key in the device must match that of
the Smart Wireless Gateway.

The Network ID and Join Key may be obtained from the Smart Wireless
Gateway on the

Setup>Network>Settings

page on the web server. The

Network ID and Join Key may be changed in the wireless device by using the
following Fast Key sequence.

Reference Information

NOTE

In order to communicate with a Field Communicator, the wired device must be
powered.

Table 4-1. THUM Adapter
HART Fast Key Sequence

Function

Key Sequence

Menu Items

Wireless Setup

1, 4

Smart Power, Network ID, Set Join
Key,

Radio State

Function

Key

Sequence

Menu Items

Device Info

2, 2, 4, 3

Manufacturer, Model, Final Assembly Number,
Universal, Field Device, Software, Hardware,
Descriptor, Message, Date, Model Number I, II,
III, SI Unit Restriction, Country

Guided Setup

2, 1

Configure, Guided Setup, Join Device to
Network, Configure Update Rate, Zero Trim,
Configure Device Display, Configure Process
Alarms

Manual Setup

2, 2

Configure, Manual Setup, Wireless, Pressure,
Device Temperatures, Device Information,
Display, Other

Wireless

2, 2, 1

Network ID, Join Device to Network, Configure
Update Rate, Configure Broadcast Power Level,
Power Mode, Power Source

«
...
36
37
38
39
40
...
»

Содержание Rosemount Smart Wireless THUM





























































Отзывы:

Нет отзывов

Похожие инструкции для Rosemount Smart Wireless THUM

Бренд: D-Link Страницы: 15

Бренд: Ampetronic Страницы: 2

Бренд: GRAS Страницы: 6

Бренд: P.I. Engineering Страницы: 4

Бренд: Microsemi Страницы: 17

PTV1000 - Push2TV - TV Adapter

Бренд: NETGEAR Страницы: 2

Бренд: Qlogic Страницы: 2

Powerline Adaptor Kit

Бренд: NETGEAR Страницы: 8

Бренд: TP-Link Страницы: 30

Бренд: Tanita Страницы: 16

Бренд: Bebob Страницы: 3

Бренд: Jabra Страницы: 15

Бренд: Jupiter Avionics Страницы: 15

Бренд: Panasonic Страницы: 1

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды