Emerson Rosemount Smart Wireless THUM Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 60

Emerson Rosemount Smart Wireless THUM Скачать руководство пользователя страница 15

Reference Manual

00809-0100-4075, Rev BA
October 2010

2-3

Smart Wireless THUM Adapter

Figure 2-2. THUM Adapter Only,
Powered by a 24 V Power
Supply with 1200 Ohm resistor
to limit current to 20 mA

The 1200 Ohm resistor should be adequately rated for the application (3W
minimum).

DEVICE NETWORK
CONFIGURATION

Join Device to Network

In order to communicate with the Smart Wireless Gateway, and ultimately the
Host System, the THUM must be configured to communicate over the
wireless network. This step is the wireless equivalent of connecting wires from
a transmitter to the host system.

1.

From the

Home

screen, select

2: Configure.

2.

Select

1: Guided Setup.

3.

Select

1: Join Device to Network.

Using a Field Communicator or AMS, enter the Network ID and Join Key so
that they match the Network ID and Join Key of the Smart Wireless Gateway
and other devices in the network. If the Network ID and Join Key are not
identical to those set in the Gateway, the THUM will not communicate with the
network. The Network ID and Join Key may be obtained from the Smart
Wireless Gateway on the

Setup>Network>Settings

page on the web server.

Configure Update Rate

The Update Rate is the frequency at which a new measurement is taken and
transmitted over the wireless network. This by default is 1 minute. This may
be changed at commissioning, or at any time via AMS Wireless Configurator.
The Update Rate is user selectable from 8 seconds to 60 minutes.

1.

From the Home screen, select

2: Configure.

2.

Select

1: Guided Setup.

3.

Select

2: Configure Update Rate.

THUM Adapter

Red

Black

White

Yellow

HART MODEM

Ground

1200
Ohm
Resistor

Green

24V
Power
Supply

+

-

Fast Keys

2, 1, 1

Fast Keys

2, 1, 2

«
...
13
14
15
16
17
...
»

Содержание Rosemount Smart Wireless THUM





























































Отзывы:

Нет отзывов