Emerson Rosemount Smart Wireless THUM Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 60

background image

Reference Manual

00809-0100-4075, Rev BA

October 2010

Smart Wireless THUM Adapter

A-2

Weight

THUM Adapter only AL - 0.65 lbs. (0.29 kg)

THUM Adapter only SST - 1.1 lbs. (0.5 kg)

AL THUM Adapter with AL remote kit - 3.2 lbs. (1.45 kg)

SST THUM Adapter with SST remote kit - 5.8 lbs. (2.65 kg)

AL THUM Adapter with M20 conduit adapter - 0.85 lbs. (.038 kg)

SST THUM Adapter with M20 conduit adapter - 1.3 lbs. (0.59 kg)

Enclosure Ratings

Housing option code D is NEMA 4X, and IP66.

Mounting

The THUM Adapter may be attached directly to the conduit of any 2- or 4-wire
HART device or mounted remotely by using the remote mount kit.

PERFORMANCE
SPECIFICATIONS

ElectroMagnetic Compatibility (EMC)

All Models:

Meets all relevant requirements of EN 61326-1 (2006) when installed with
shielded wiring. The sub-device must also use shielded wiring for installation.

Vibration Effect

Output unaffected when tested per the requirements of IEC60770-1 field with
general application or pipeline with low vibration level (10-60 Hz 0.15 mm
displacement peak amplitude / 60-500 Hz 2g).

When the THUM Adapter is used on wired devices that are subject to
vibration levels greater than 2g, it is recommended that the THUM Adapter be
remotely mounted using the remote mount kit.

Temperature Limits

Output Specifications

The THUM allows Wireless communication between the HART device it is
connected to and the Smart Wireless Gateway.

Operating Limit

Storage Limit

–40 to 185 °F
–40 to 85 °C

–40 to 185 °F
–40 to 85 °C

«
...
44
45
46
47
48
...
»

Содержание Rosemount Smart Wireless THUM





























































Отзывы:

Нет отзывов

Похожие инструкции для Rosemount Smart Wireless THUM

Бренд: Qlogic Страницы: 2

SANblade 2300 Series

Бренд: Qlogic Страницы: 108

Бренд: Qlogic Страницы: 2

Бренд: Qlogic Страницы: 2

SANblade QLA2342

Бренд: Qlogic Страницы: 16

SANblade QLA4050

Бренд: Qlogic Страницы: 4

Bluetooth USB-Adapter Version 1.2

Бренд: Hama Страницы: 8

Бренд: TRENDnet Страницы: 15

RTE7702012EAB00000J

Бренд: Renesas Страницы: 53

Бренд: Diamond Multimedia Страницы: 14

Бренд: Synapse Страницы: 33

Бренд: Dante Страницы: 2

ExpressSAS R380

Бренд: ATTO Technology Страницы: 2

Бренд: AR Страницы: 20

Бренд: TP-Link Страницы: 32

WebLogic Server

Бренд: BEA Страницы: 294

Бренд: Keysight Technologies Страницы: 37

iPush2TV FS910347

Бренд: FirstSing Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды