manualshive.com logo in svg

Emerson Rosemount 644 FOUNDATION, Справочное руководство

Поделиться
Скачать
Emerson Rosemount 644 FOUNDATION Скачать руководство пользователя страница 40

34

Reference Manual

00809-0400-4728, Rev CA

Installation

September 2018

Installation

3.4.3

LCD display installation

The LCD display provides local indication of the transmitter output and abbreviated diagnostic messages 
governing transmitter operation. Transmitters ordered with the LCD display are shipped with the meter 
installed. After-market installation of the meter can be performed if the transmitter has a meter 
connector (transmitter revision 5.5.2 or later). After-market installation requires the meter kit 
(part number 00644-4430-0001), which includes:

LCD display assembly (includes LCD display, meter spacer, and two screws)

Meter cover with O-ring in place

Figure 3-4. Installing the LCD Display

Use the following procedure to install the meter.

1. If the transmitter is installed in a loop, secure the loop and disconnect the power. If the transmitter is 

installed in an enclosure, remove the cover from the enclosure. 

2. Decide meter orientation (the meter can be rotated in 90° increments). To change meter orientation, 

remove the screws located above and below the display screen. Lift the meter off the meter spacer. 
Remove the 8-pin plug and re-insert it in the location that will result in the desired viewing 
orientation.

3. Reattach the meter to the meter spacer using the screws. If the meter was rotated 90° from its 

original position, it will be necessary to remove the screws from their original holes and re-insert 
them in the adjacent screw’s holes.

4. Line up the 10-pin connector with the 10-pin socket and push the meter into the transmitter until it 

snaps into place. 

5. Attach the meter cover; tighten at least one-third turn after the O-ring contacts the transmitter 

housing. The cover must be fully engaged to meet explosion-proof requirements.

6. Use a Field Communicator, AMS software, or a F

OUNDATION

 Fieldbus Communication tool to configure 

the meter to the desired display. 

Note

Observe the following LCD display temperature limits:
Operating: –4 to 185 °F (–20 to 85 °C)
Storage: –50 to 185 °F (–45 to 85 °C)

A. LCD display
B. 10-pin connector
C. Meter space

D. Captive mounting screws and springs
E. Rosemount 644H

A

C

B

D

E

Содержание Rosemount 644 FOUNDATION

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды