manualshive.com logo in svg

Emerson Rosemount 228, Справочное руководство, Страница: 7 / 44

Поделиться
Скачать
Emerson Rosemount 228 Скачать руководство пользователя страница 7

1

Description and specifications

1.1

Description

The Rosemount 222 toroidal flow through conductivity sensor measures conductivity in
highly conductive liquids up to 2 S/cm (2,000,000 

μ

S/cm). A noninvasive flow through

design allows for in-line installations without any obstruction to sample and makes these
sensors ideal for use with viscous or fibrous liquids.

1.2

Unpacking and inspection

Complete the following steps when you unpack your instrument.
1.

Inspect the shipping container. If there is damage, contact the shipper immediately
for instructions.

2.

If there is no apparent damage, and remove the sensor.

3.

Ensure that all items shown on the packing list are present. If items are missing,
contact your local Customer Care representative.

4.

Save the shipping container and packaging.

They can be reused to return the sensor to the factory in case of damage.

1.3

Sensor Specifications

Sensor specifications

Table 1-1:   

Sensor specification

Description

Wetted materials

Body materials either glass-filled PEEK, glass-filled Tefzel,
or unfilled Tefzel. Option -20 has EPDM gasket

Process connection

-20: 5/8 in. 11 UNC, -21: 3/4 in. MNPT

Cable length

20 ft (6.1 m)

Maximum cable length

200 ft (61.0 m)

Weight/shipping weight

2 lb / 3 lb (1.0 kg / 1.5 kg)

Maximum operating temperature and pressure

Table 1-2:   

Body material option

Maximum temperature

Maximum pressure

Maximum pressure (for
CRN registration only)

-02 (Glass-filled PEEK
(standard temperature))

248 °F (120 °C)

295 psig (2135 kPa)

220 psig (1618 kPa [abs])

Description and specifications

Rosemount 228 Sensor

1

Содержание Rosemount 228













































Отзывы:

Нет отзывов