Emerson Rosemount 228 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 44

Emerson Rosemount 228 Скачать руководство пользователя страница 14

Insertion adapter 2001990 for use with 3/4 in. MNPT threaded process

connection (-21 option)

Figure 2-4:

Procedure

1.

Mount the sensor in the pipe.

2.

Keep at least 1 in. (2.5 cm) between the sensor and pipe walls.

If the clearance is too small, calibrate the sensor in place.

3.

Mount the sensor in a vertical pipe run with flow from top to bottom.

If the sensor must be mounted in a horizontal pipe run, orient the sensor in the
3 o'clock or 9 o'clock position.

4.

Ensure that the sensor is completely submerged in liquid.

2.2

Insertion/Retraction Assembly Installation

Requirements

Insertion/Retraction Assembly Installation Requirements

Table 2-1:

Requirement

Description

Process connection

1-1/2 in. Larger openings may keep the sensor
from inserting far enough into the process liq-
uid.

Line size

3 in.; 2 in. line requires in-place calibration.

Valve

1-1/2 in. NPT full port valve (PN 9340065)

Retraction clearance

2 ft (0.6 m)

Excess vibration

Provide mechanical support if excess vibration is
expected.

Install

8

Reference Manual

«
...
12
13
14
15
16
...
»

Содержание Rosemount 228













































Отзывы:

Нет отзывов