background image

3

PENBERTHY 

MODEL MGS-314 SERIES AND MGS-314D SERIES LEVEL CONTROL SWITCH

INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS

4.2 Mounting the switch 

Due to shipping vibration, it is possible the 
magnet toggle will not be in the 'normal' 
position for proper operation. If this occurs, 
simply cycle the float past the switch once. 
This will initialize it automatically.
1.  Measure the distance from the top of the 

indicating scale, on the magnetic level 
meter, to the top of the communicating 
chamber. Record this distance. 

2.  Loosen the clamps holding the indicating 

scale to the communicating chamber.

3.  Open the mounting band supplied with the 

MGS-314/314D Series and put it around 
the communicating chamber, under the 
indicating scale. 

4.  Place the MGS-314/314D Series on 

the communicating chamber with the 
cooling fins facing 180° away from the 
communicating chamber and with the 
conduit opening facing down. 

Position 'A'

Position 'B' 

Position 'B'

Figure 2 

MGS-314D SERIES

Figure 1

MGS-314 SERIES

Position 'A'

Toggle

Toggle

Toggle

Toggle

4.3 Wiring connection  

1.  If you are using conduit for the switch wiring 

use a conduit seal with a drain or a drip-loop to 
prevent condensate from entering the housing. 
Condensate can cause electrical shorts.

  The switch housing has a ½" NPT-F 

connection for the wiring conduit. 

2.  We recommend attaching an aluminum 

condulet, via a 300 Series stainless steel 
nipple, to the conduit opening of the switch 
housing. This will give you an accessible point 
to terminate the control wires. DO NOT USE 
any ferromagnetic material such as: carbon 
steel, duplex, 400 Series stainless steel or 
cast iron.

5.  Put the mounting band between the cooling 

fins in the channel provided. 

6.  Loosely tighten the mounting band. Move 

the MGS-314/314D Series either up or down 
to the desired position, and tighten the band. 

7.  The switch must be mounted within the 

indication range for the magnetic gauge. 
The mounting band for the switch should be 
a minimum of 1" inside the indication range. 
This will insure sufficient float movement to 
operate the switch. 

8.  If more than one switch is used on a 

single magnetic gauge, the minimum 
recommended distance between mounting 
bands is 3". 

9.  Adjust the position of the indicating scale so 

that the distance from the top of the scale 
to the top of the communicating chamber 
is the same as in Step 1. Tighten the 
clamps holding the indicating scale to the 
communicating chamber. 

Содержание Penberthy MGS-314 Series










Отзывы: