Emerson MRLDS-250 Скачать руководство пользователя страница 15

Страница: 15 / 40

Overview

Wiring and Configuration • 9

Wiring and

Configuration

3.1.

Overview

Prior to wiring and configuring the MRLDS-250,

ensure the following conditions have been met:

•MRLDS-250 backplate is mounted in an appropriate

location.

•The cover panel is removed.

•If the cover panel was reattached after mounting,

open the gas detector enclosure by pressing the top

latch with a suitable screwdriver or other flat blade.

With the top latch depressed pull the housing apart by

grasping the sides and pulling straight out. Align and

press together to close.

Figure 3-1

- Terminal Blocks and Cable Glands

NOTE: The pre-installed cable

gland (left) and the optional cable

on the gland (right) have a 1/4

cable capacity (each).

NOTE: Install the optional cable

gland in the right side of the base

unit if needed. Otherwise, install

the blanking plug that is included

in the mounting kit.

3.2.

Wiring Supply Power

(24VAC or 24VDC)

CAUTION: Incorrect wiring may

permanently damage the gas

detector and void the warranty.

Double check all terminations

before applying power.

Either 24VAC or 24VDC may be used to power the

MRLDS-250. Connect wiring to the appropriate

terminal locations (see

Table 3-1

. Use two wires,

between 14 and 22 AWG. Refer to

Figure 3-2

for (AC

wiring left) or DC wiring (right).

Figure 3-2

- Supply Power Wiring Options

Table 3-1

- Power Options and Terminal Block

Connections

Power

Option

Pin

Label

Wiring

Termination

24 VAC

24V AC line

24V AC

neutral

24 VDC

24V DC

positive

GND

24V DC

ground

Содержание MRLDS-250









































Результаты поиска

Содержание MRLDS-250

Отзывы:

Похожие инструкции для MRLDS-250

Бренды по названию

Популярные бренды

Emerson MRLDS-250, Инструкция по установке и эксплуатации

Результаты поиска

Содержание MRLDS-250

Отзывы:

Похожие инструкции для MRLDS-250

Бренды по названию

Популярные бренды