Emerson Micro Motion 3300 Скачать руководство пользователя страница 25

Страница: 25 / 27

Installation Manual

Wiring

Figure 3-17: 9-wire cable to core processor

3. Ground the cable.

4. Ensure the integrity of the gaskets, grease all O-rings, then close the junction box

housing and core processor end-cap, and tighten all screws.

3.4

Connect the power supply wiring

Cable type

Procedure

Jacketed cable

Ground the shield drain wires (the black wire) only on the core

processor end, by connecting it to the ground screw inside the

lower conduit ring. Do not ground to the core processor’s

mounting screw. Do not ground the cable at the sensor junction

box.

Shielded or armored cable

Ground the shield drain wires (the black wire) only on the core

processor end, by connecting it to the ground screw inside the

lower conduit ring. Do not ground to the core processor’s

mounting screw. Do not ground the cable at the sensor junction

box.

Ground the cable braid on both ends, by terminating it inside the

cable glands.

CAUTION!

Make sure that the wires are not caught or pinched when you close the housing to reduce the risk of
measurement error or meter failure.

CAUTION!

• Do not install power supply wiring in the same cable tray or conduit as the input/output

wiring to avoid device failure or measurement error.

• Shut off the power supply before installing the applications platform.
• Make sure the power supply voltage matches the voltage that is indicated on the power

supply wiring terminals. See

Figure 3-18

Brown

Red

Green

White
Blue

Gray
Orange

Violet

Yellow

Black

(Drains from all

wire sets)

Plug and

socket

Mounting screw

Blue

Gray

Orange

Red

Green

White

Brown

Violet

Yellow

Ground screw

Black

9-wire cable from sensor

Core processor

Содержание Micro Motion 3300




























Результаты поиска

Содержание Micro Motion 3300

Отзывы:

Похожие инструкции для Micro Motion 3300

Бренды по названию

Популярные бренды

Emerson Micro Motion 3300, Руководство по установке

Результаты поиска

Содержание Micro Motion 3300

Отзывы:

Похожие инструкции для Micro Motion 3300

Бренды по названию

Популярные бренды