Emerson HVAC Drive H300 Скачать руководство пользователя страница 32

Страница: 32 / 40

Electronic Bypass Controller Installation and Commissioning Guide

Section 6 - Alarm & Faults

There are two different locations a fault or alarm will be displayed:

1. The electronic bypass keypad
2. The VFD keypad

6.1 Electronic Bypass Keypad Alarms and Faults

There are four (4) Alarm LEDs on the electronic bypass keypad indicating the faults
that may occur. They are as follows:

Motor Overload:

Indicates that the manual motor overload relay has tripped.

Check that overload relay is properly set for motors full load Ampere rating. Check
for excessive motor current and load.

Safety:

Indicates that an external safety interlock is in the open position.

If a safety input is not used, check the bypass terminal block for a jumper between
terminals TB2-3 and TB2-8. If a safety input is used, verify that the safety contact
is closed.

Incoming

Power

Power On

1 Select Operation Mode

RUN

(1) Rest mechanical overload inside enclosure

2 Select Run Mode

Input

Contactor

Bypass

Contactor

Output

Contactor

Press OFF/RESET once to cancel RUN mode

Press OFF/RESET twice to cancel OPERATION mode

TEST

HAND

VFD

AUTO

OFF

RESET

BYPASS

VFD

Alarm Display

Motor (1)

Overload

External

Safety

Fire

Alarm

VFD

Fault

Содержание HVAC Drive H300









































Результаты поиска

Содержание HVAC Drive H300

Отзывы:

Похожие инструкции для HVAC Drive H300

Бренды по названию

Популярные бренды

Emerson HVAC Drive H300, Руководство по установке и пусконаладке

Результаты поиска

Содержание HVAC Drive H300

Отзывы:

Похожие инструкции для HVAC Drive H300

Бренды по названию

Популярные бренды