background image

FL Series

D103068X012

Instruction Manual
Form 5733

July 2004

www.FISHERregulators.com

FL Series Pressure Reducing Regulators

Introduction

Scope of Manual

This manual provides instructions for installation,
adjustment, maintenance, and parts ordering for the FL
Series regulators.

Description

The FL Series regulators are accurate pilot-operated,
pressure balanced, soft seated regulators designed for
high pressure transmission/city gate, large capacity
distribution systems and power plant feeds.  The FL
Series provides smooth, quiet operation, tight shutoff and
long life.  The regulator utilizes a main valve actuator, a
Type PRX pressure reducing pilot, and a Type SA/2 pilot

supply pressure regulator.  The Type PRX pilot uses inlet
pressure reduced by a Type SA/2 supply pressure
regulator, as loading pressure to operate the main valve
actuator.  The outlet pressure is sensed through a
control line on the main valve actuator and also on the
Type PRX pilot diaphragm.

Specifications

The Specifications section gives some general specifi-
cations for the FL Series regulators. The nameplates
give detailed information for a particular regulator as it
comes from the factory.

Type FL

E0820

Type  MFL with Type SRS Silencer

E0821

Figure 1.  Type FL and Type MFL with Type SRS Silencer

Содержание FL

















Отзывы: