Emerson Fisher POSI-SEAL A81 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 24

background image

Instruction Manual

D103302X012

A81 Valve

January 2011

15

Assembly

WARNING

Do not lubricate bearings that will be used for oxygen service, or where the lubrication is incompatible with the process
media. Any use of lubricant can lead to the sudden explosion of media due to the oil/oxygen mixture, causing personal
injury or property damage.

CAUTION

To avoid possible product damage, ensure the bearing tabs are oriented correctly when installing in the following
procedure. See figure 5 for proper orientation of the bearings.

Figure 6. Taper / Expansion Pin Installation

TAPER/EXPANSION PIN LOCATION

INSTALL THE PINS FROM THIS SIDE OF THE DISK.

1

“T” STAMPED ON ACTUATOR
END OF DISK

W9487

1

«
...
13
14
15
16
17
...
»

Содержание Fisher POSI-SEAL A81

























Отзывы:

Нет отзывов

Похожие инструкции для Fisher POSI-SEAL A81

Бренд: ABB Страницы: 370

Бренд: ABB Страницы: 17

Бренд: ABB Страницы: 104

Бренд: ABB Страницы: 120

Бренд: ABB Страницы: 42

Бренд: GE Страницы: 2

Бренд: XOXO Modular Страницы: 13

Бренд: Balboa Water Group Страницы: 28

Бренд: Jafar Страницы: 10

Бренд: Jafar Страницы: 8

ServeRAID M5014

Бренд: IBM Страницы: 106

Бренд: Bartec Страницы: 26

Бренд: V2 Страницы: 48

Бренд: Lawler Страницы: 6

Бренд: Data Aire Страницы: 28

COOPER POWER SERIES

Бренд: Eaton Страницы: 50

Бренд: ICP DAS USA Страницы: 4

Бренд: ICP DAS USA Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды