background image

www.Fisher.com

Fisher

 NPS 8 CHP Control Valve

Contents

Introduction

1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Scope of Manual

1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Description

2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Specifications

2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installation

3

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Lifting Guidelines

3

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Maintenance

4

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Packing Maintenance

6

. . . . . . . . . . . . . . . . . . . . . . . . .

Adding Packing Rings

7

. . . . . . . . . . . . . . . . . . . . .

Replacing Packing

7

. . . . . . . . . . . . . . . . . . . . . . . .

Trim Removal

10

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Valve Plug Maintenance

10

. . . . . . . . . . . . . . . . . . . . .

Lapping Seats

11

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Trim Replacement

11

. . . . . . . . . . . . . . . . . . . . . . . . . .

Parts Ordering

12

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Parts List

13

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 1. Fisher CHP NPS 8 Control Valve

X1365

Introduction

Scope of Manual

This instruction manual includes installation, maintenance, and parts information for the Fisher CHP control valve.
Refer to separate manuals for instructions covering the actuator, positioner, and accessories.

Do not install, operate, or maintain CHP valves without being fully trained and qualified in valve, actuator, and
accessory installation, operation, and maintenance. 

To avoid personal injury or property damage, it is important to

carefully read, understand, and follow all the contents of this manual, including all safety cautions and warnings.

 If you

have any questions about these instructions, contact your 

Emerson Process Management sales office

 before

proceeding.

Instruction Manual

D104197X012

NPS 8 CHP Valve

September 2016

Содержание Fisher NPS 8 CHP















Отзывы: