manualshive.com logo in svg

Emerson Fisher Level-Trol 2502 Series, Инструкция по эксплуатации, Страница: 20 / 28

Поделиться
Скачать
Emerson Fisher Level-Trol 2502 Series Скачать руководство пользователя страница 20

2502 Series Controllers

Instruction Manual

Form 1446

November 2006

20

3.  Remove any insulating tape from the joint

between the controller case and the torque tube

arm. Remove the four cap screws (key 39, figure 12)

that hold the controller or heat insulator to the torque

tube arm. Pull the case straight out from the torque

tube arm, easing it over the shaft coupling (key 36,

figure 12) if one is installed.
4.  If the controller has a heat insulator, remove the

button head cap screws (key 40). Remove four

washers (key 53) and the insulator assembly 

(key 35).

Changing Mounting Method

WARNING

To avoid personal injury from contact

with the process liquid, lower the

vessel level below the torque-tube arm

before proceeding. For closed vessels,

release any pressure that may be

above the liquid. Also, be careful to

avoid overloading a thin-wall torque

tube and/or oversized displacer.

Refer to figure 14 for key number locations.

1.  Remove the controller as described previously.
2.  A controller is attached to the sensor in one or

the other of the mounting positions shown in 

figure 4. Right hand mount is with the case to the

right of the displacer when looking at the front of the

case. Left hand mount is with the case to the left of

the displacer. For a 249 Series sensor, remove the

torque tube arm from the sensor or vessel and

reinstall the torque tube arm in the opposite position

according to the appropriate instruction manual.
3.  Check the desired control action to determine if it

is also necessary to reverse the controller action.

The nozzle block and bellows tubing should be

arranged in the proper position as shown in 

figure 13.
4.  Remove the RAISE LEVEL dial, turn it over, and

install it in the desired position. The arrow on it under

the word FLOAT should point toward the displacer.

On a controller with indicator assembly, remove two

screws (key 41, figure 14), turn the front plate 

(key 54, figure 14) to the side that will have the float

arrow pointing toward the displacer, and secure the

plate with the screws.
5.  Install the controller according to the next section.

20A7423-C/DOC

Figure 12. Heat Insulator Shown Installed on 249 Series

Installing Controller on Sensor

Note

If the installation is in a location that is

not readily accessible and shop

calibration is required, remove the

torque tube arm from the cage or

vessel before mating the controller to

the sensor. Install the controller on the

torque tube arm in the shop; then

calibrate and return the controller and

torque tube arm assembly to the

installation.

Perform step 1 only if adding a heat insulator to

a unit that does not have one. Key numbers in

this step are shown in figure 12, unless

otherwise indicated.

1.  To install the heat insulator, secure the shaft

extension (key 37) to the torque tube assembly

rotary shaft with the shaft coupling (key 36). Tighten

both set screws (key 38), with the coupling centered

Содержание Fisher Level-Trol 2502 Series





























Отзывы:

Нет отзывов