manualshive.com logo in svg

Emerson Fisher Level-Trol 2502 Series, Инструкция по эксплуатации, Страница: 22 / 28

Поделиться
Скачать
Emerson Fisher Level-Trol 2502 Series Скачать руководство пользователя страница 22

2502 Series Controllers

Instruction Manual

Form 1446

November 2006

22

AV2323-A
AV2322-A
B0995-2/IL

SEAL

SCREW

SEAL

SCREW

RING

SEAL

SCREW

SEAL

SCREW

RING

FLAPPER

HOOK

FLAPPER

HOOK

PROPORTIONAL

TUBING

RESET

TUBING

RESET

TUBING

PROPORTIONAL

TUBING

RESET

VALVE

RESET

VALVE

SEAL

SCREW

RINGS

SEAL

SCREWS

TO RELAY

TO RELAY

TO

PROPORTIONAL

VALVE

TO

PROPORTIONAL

VALVE

DIRECT ACTING—RIGHT HAND MOUNTING

REVERSE ACTING—LEFT HAND MOUNTING

REVERSE ACTING—RIGHT HAND MOUNTING

DIRECT ACTING—LEFT HAND MOUNTING

Figure 13. Nozzle, Flapper, and Tubing Arrangements

for Various Actions and Mountings

4.  Install a new gasket, the replacement relay if

necessary, and both mounting screws. Reconnect

the tubing. On a controller with indicator assembly,

slide the base plate under the two lower screws of

the relay case, align the plate so that the pointer will

read properly, and tighten the screws.

Replacing Bellows

Key numbers are shown in figure 14.

1.  To gain access to the lower bellows, remove the

relay according to the Changing Relay section.

2.  Remove the upper and lower bellows frame

screws (key 96) that hold both bellows assemblies to

the bellows frame. Unscrew each bellows from the

spacer (key 98), being careful not to lose the O-ring

(key 57, not shown) from the spacer end of the

bellows.

3.  Inspect each bellows and O-ring and replace if

necessary, using an unpainted bellows for a 0.2 

to 1.0 bar (3 to 15 psig) range and a red bellows for

a 0.4 to 2.0 bar (6 to 30 psig) range. Be sure to

install the O-ring at the spacer end of the bellows.

4.  Install each bellows by screwing it down over the

stud (key 97, not shown) protruding from each end

of the spacer. Secure with a bellows frame screw,

and install the relay according to the Changing Relay

section.

5.  Perform the calibration procedure and any other

necessary part of the calibration sequence.

Reversing Action

Note

The following procedure will be

necessary to restore previous action if

the mounting method has been

changed. Key numbers are shown in

figure 14.

1.  Remove two screws (keys 63 and 64), two seal

rings (key 55), and the nozzle block (key 101).

Check seal ring condition and replace rings as

necessary.
2.  Install the nozzle block, seal rings, and screws on

the opposite side of the beam as shown in figure 13.

Disconnect the proportional band tubing (key 76)

and one of the two pieces of reset tubing (key 75)

from the bellows frame (key 94) and reconnect them

in the proper orientation as shown in figure 13.

Содержание Fisher Level-Trol 2502 Series





























Отзывы:

Нет отзывов