Emerson Fisher 3582 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 56

background image

Instruction Manual

D200138X012

3582, 582i, and 3583

January 2013

13

Mounting

Key numbers used in this procedure are shown in figure 2 except where indicated.

1. Figure 2 shows the various mounting parts required for mounting on Fisher actuators. Mounting parts for actuators

that require spacers have the spacers (key 50) included. 657 and 667 actuators, sizes 70 through 100, with or
without a side‐mounted handwheel, use spacers (keys 97 and 102) between the stem connector and the connector
arm (key 48). On all other actuators that use spacers, place the spacers (key 50) between the mounting plate
(key 63) and the actuator mounting boss.

When mounting the valve positioner or valve stem position transmitter on an actuator by another manufacturer,
provide spacers, if necessary, by cutting sections from 1/2 or 3/8‐inch pipe so that the “X” dimension matches the
value given in figure 3.

Figure 2. Mounting Assembly

41B8569‐D SHT 1 AND 2

657, 657MO, 667, 667MO
SIZE 80 UP TO 51 mm (2 IN) TRAVEL

657
SIZE 70, 87 UP TO 51 mm (2 IN) TRAVEL

67CFR

657, 657MO, 667, 667MO
SIZE 100 ALL TRAVEL
657, 657MO, 667, 667MO
SIZE 80 52 TO 76 mm (2.0625 TO 3 IN) TRAVEL
657MO, 667MO
SIZE 70, 87 78 TO 102 mm (3.0625 TO 4 IN) TRAVEL
657‐4MO, 667‐4MO
SIZE 70, 87 102 mm (4 IN) TRAVEL

657MO, 667MO
SIZE 70, 87 UP TO 78 mm (3 IN) TRAVEL

513
SIZE 32
656
ALL SIZES
657MO
SIZE 34, 45, 50, 60
657‐4, 667‐4
SIZE 70, 87 102 mm (4 IN) TRAVEL
657, 667
SIZE 70, 87 78 TO 102 mm (3.0625 TO 4 IN) TRAVEL
667
SIZE 70, 87, 52 TO 78 mm (2.0625 TO 3 IN) TRAVEL

NOTE:
KEY 55 (TUBING CONNECTOR) NOT SHOWN

«
...
11
12
13
14
15
...
»

Содержание Fisher 3582

























































Отзывы:

Нет отзывов

Похожие инструкции для Fisher 3582

Бренд: Nelsen Corporation Страницы: 16

Бренд: National Instruments Страницы: 34

AirGENIO SUPERIOR

Бренд: 2VV Страницы: 27

Бренд: Vasco Страницы: 32

Бренд: Abra Страницы: 16

Бренд: SAI Страницы: 16

Бренд: Hable Страницы: 3

Бренд: Baader Planetarium Страницы: 7

Бренд: Beaphar Страницы: 2

Бренд: Danfoss Страницы: 24

Бренд: FAAC Страницы: 4

Бренд: FAAC Страницы: 52

Бренд: UCS Страницы: 4

coviva Smartbox TKP100A

Бренд: hager Страницы: 4

Бренд: Vag Страницы: 12

Бренд: Jabra Страницы: 8

Бренд: L-Acoustics Страницы: 20

ArtNet-DMX Mux16

Бренд: DMX4ALL Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды