Emerson Fisher 3582 Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 56

background image

Instruction Manual

D200138X012

3582, 582i, and 3583

January 2013

54

Diagnostic Connections (figure 8)

FlowScanner

t

valve diagnostics system hook‐up.

Includes connector body and body protector. If
ordered for units with gauges, a stem is also included.

Note

Part numbers are shown for recommended spares only. For part
numbers not shown, contact your Emerson Process Management sales
office.

Description

For 3582 pneumatic valve positioners
For units w/gauges
SST fittings
brass fittings

For units w/o gauges
SST fittings
brass fittings

For 3582i electro‐pneumatic valve positioners
For units w/gauges
SST fittings
brass fittings

For units w/o gauges
SST fittings
brass fittings

Loop Schematics/Nameplates

This section includes loop schematics required for wiring of intrinsically safe installations. It also contains typical
approvals nameplates. If you have any questions, contact your Emerson Process Management sales office.

GE28591 Rev A

NOTES:

1. BARRIERS MUST BE CSA CERTIFIED WITH ENTITY PARAMETERS
AND ARE TO BE INSTALLED IN ACCORDANCE WITH THE
MANUFACTURER'S I.S. INSTALLATION INSTRUCTIONS.
2. EQUIPMENT SHALL BE INSTALLED IN ACCORDANCE WITH THE
CANADIAN ELECTRICAL CODE, PART I.
3. FOR ENTITY INSTALLATION (I.S. AND N.I.): Vmax > Voc, Imax > Isc
Ci + Ccable < Ca, Li + Lcable < La

Figure 28. CSA Loop Schematic for Fisher 582i Converter

«
...
52
53
54
55
56
»

Содержание Fisher 3582

























































Отзывы:

Нет отзывов

Похожие инструкции для Fisher 3582

Бренд: Jetline Страницы: 58

Бренд: PESA Страницы: 30

Бренд: M-system Страницы: 3

RDS17S-ELITE1-R1

Бренд: D&R ELECTRONICS Страницы: 12

iDual A E27 iD60

Бренд: jedi LIGHTING Страницы: 23

Бренд: HEROSE Страницы: 92

Бренд: Samson Страницы: 70

Бренд: Keysight Technologies Страницы: 105

Бренд: Festo Страницы: 87

Бренд: Anthem Страницы: 8

Бренд: National Instruments Страницы: 11

Бренд: DAY Страницы: 23

Lift Inverter L1000V

Бренд: YASKAWA Страницы: 282

Бренд: CP Electronics Страницы: 12

Бренд: Kelly Страницы: 32

Бренд: Eazyzap Страницы: 32

TOP-43 EE Series

Бренд: CAME Страницы: 2

Бренд: WattMaster Страницы: 104

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды