Emerson Fisher 3582 Скачать руководство пользователя страница 10

Страница: 10 / 56

Instruction Manual

D200138X012

3582, 582i, and 3583

January 2013

ATEX

Standards Used for Certification

EN 60079-0: 2006

EN 61241-0: 2006

EN 60079-1: 2007

EN 61241-1: 2004

EN 60079-11: 2007

EN 61241-11: 2006

EN 60079-15: 2005

Special Conditions for Safe Use

Intrinsically Safe, Dust

This equipment is intrinsically safe and can be used in potentially explosive atmospheres.

The electrical parameters of certified equipment which can be connected to the device must not exceed one of these
following values:

≤

30 Vdc ; Io

≤

150 mA ; Po

≤

1.25 W

Ambient temperature:

T6, at Tamb = 47

C ; T5, at Tamb = 62

C ; T4, at Tamb = 71

Flameproof, Dust

The flame path is other than required by EN 60079‐1. Contact the manufacturer for information on the dimensions of
the flameproof joints.

Electrical connections are typically made using either cable or conduit.

If using a cable connection, the cable entry device shall be certified in type of explosion protection flameproof

enclosure “d”, suitable for the conditions of use and correctly installed.

For ambient temperatures over 70

C, cables and cable glands suitable for at least 90

C shall be used.

If using a rigid conduit connection, an Ex d certified sealing device such as a conduit seal with setting compound

shall be provided immediately to the entrance of the enclosure.

For ambient temperatures over 70

C, the wiring and setting compound in the conduit seal shall be suitable for at least

Type n, Dust

No special conditions for safe use.

Refer to table 6 for additional information and figure 31 for a typical ATEX/IECEx approval nameplate.

Содержание Fisher 3582

























































Результаты поиска

Содержание Fisher 3582

Отзывы:

Похожие инструкции для Fisher 3582

Бренды по названию

Популярные бренды

Emerson Fisher 3582, Инструкция по эксплуатации

Результаты поиска

Содержание Fisher 3582

Отзывы:

Похожие инструкции для Fisher 3582

Бренды по названию

Популярные бренды