Emerson ENARDO 8 Series Скачать руководство пользователя

Страница: 10 / 12

8 Series

MODEL

PART NUMBER

Standard Gasket

(Compressed Fiber)

High Temperature Gasket

(Graphite Base)

80802, 80803, 80804

7008125

7049223

81206

7008136

7049236

81608

7008107

7049207

82010

7008109

7049209

82412

7008111

7049211

82814

7008113

7049213

83016

7008114

7049214

83620

7008117

7049217

1. Two (2) required per assembly.

Table 7.

Part Numbers for Replacement Element Assembly Gaskets

(1)

Parts List

Recommended Spare Parts

For installations that require frequent maintenance and

minimum downtime it is recommended that the user

purchase a spare element assembly and several spare

element gaskets. The spare element assembly can

be installed immediately and the dirty assembly can

then be cleaned and be stored as a spare for the next

maintenance interval.

Note

Element gaskets should be replaced

each time the cell assembly is loosened

and removed to insure a gas tight seal.

Parts Ordering

When corresponding with your local Sales Office about

this equipment, always reference the equipment serial

number stamped on the nameplate.

When ordering replacement parts, specify the

complete 7-character part number of each required

part as found in the following parts list.

Содержание ENARDO 8 Series













Результаты поиска

Содержание ENARDO 8 Series

Отзывы:

Похожие инструкции для ENARDO 8 Series

Бренды по названию

Популярные бренды

Emerson ENARDO 8 Series, Инструкция по эксплуатации

Результаты поиска

Содержание ENARDO 8 Series

Отзывы:

Похожие инструкции для ENARDO 8 Series

Бренды по названию

Популярные бренды