manualshive.com logo in svg

Emerson Easyheat GC-1, Руководство по обслуживанию

Поделиться
Скачать
Emerson Easyheat GC-1 Скачать руководство пользователя страница 15

Grinder Replacement

Installing Grinder

DANGER

  SHOCK HAZARD! 
  Turn off electrical 

power at circuit breaker, use voltmeter 

or circuit tester to ensure that 
POWER IS OFF.

1.  Place mounting flange up over existing 

collar adaptor connection lip.

2.  Push mounting flange up and out-of-

the-way, and fit the mounting gasket 
onto the sink bowl connection lip.

3.  Move mounting flange down over the 

mounting gasket. Be certain that the 
threaded fasteners in the mounting 
flange fit in the recesses in the top of 
the mounting gasket.

4.  Position the grinder under the

mounting gasket.

5.  Turn legs with channel-lock pliers to 

rise the grinder so that it aligns with 
the holes in the mounting gasket.

6.  Install the six screws through the 

grinder body flange and into the 
mounting flange and secure.

7.  Adjust legs so that the unit is sup-

ported evenly. Push o-ring on each leg 
upwards, flush with bottom of cover. 
(Refer to step 5 image.)

8.  Secure legs in position by adjusting the 

lower two jam nuts into place against 
the adjustable portion of the leg and 
each other.

9.  Lock jam nuts in place by turning the 

lower nut clockwise and rotating the 
secondary nut counterclockwise until 
snug, locking nuts against each other 
repeat process for all three legs.

step 

2

step 

4

step 

6

step 

1

step 

3

step 

5

step 

9

step 

8

grind2energy.com

 

Grind2Energy Technical Support: 844-874-7529     |     13

  

G2E015-15F-89-84

Содержание Easyheat GC-1























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды