Emerson Easyheat GC-1 Скачать руководство пользователя страница 10

Страница: 10 / 22

WARNING

SHOCK HAZARD! Turn off

electrical power at circuit breaker,

use voltmeter or circuit tester to

ensure that POWER IS OFF.

Wiring Connections

Incoming power supply requires that:

• Ground wire is securely fastened to

panel as shown.

• 208-230V system use #8 AWG wire

from line disconnect switch and control
box.

• 460V system use #12 AWG wire from

line disconnect switch to control box.

The pump lead wires are connected to

"T1, T2 & T3" as shown below.

The grinder lead wires are connected

to "M1, M2 & M3" as shown below.

The pressure switch leads are con-

nected to the control panel as shown
below (black to black, brown to brown,
blue to blue).

The lead wire for the tank float switch

is connected to terminal connections 2
and 15 as shown below. This wire runs
along the length of the discharge line
to the tank.

The 5gpm solenoid valve lead wires

are connected to terminal 11 & 12 as
shown below.

The 2gpm solenoid valve lead wires are

connected to terminal 7 & 10 as shown
below.

Grind2Energy

™

System

Wiring Connections

Adjust

Power Supply

INPUT

DC ok

1 ON

0 OFF

2 2 2 4 4 4 7 10 11 12 15 M1 M2 M3 T1 T2 T3

GROUND

BLK BRN

BLU

TANK

FLUSH

START

STOP

WARNING

ELECTRICAL SHOCK HAZARD. DISCONNECT INCOMING POWER
BEFORE SERVICING CONTROL CENTER. FAILURE TO DO SO COULD
RESULT IN DEATH OR SERIOUS PERSONAL INJURY. DOOR
INTERLOCK SWITCHED DISCONNECT CONTROL CIRCUIT ONLY.

PRESS IF
JAMMED

Control Box

INCOMING

POWER

PUMP

GRINDER

FLOAT

SWITCH

2 GPM

SOLENOID

PRESSURE

SWITCH

5 GPM

SOLENOID

grind2energy.com

Grind2Energy Technical Support: 844-874-7529 | 8

G2E015-15F-89-84

Содержание Easyheat GC-1























Результаты поиска

Содержание Easyheat GC-1

Отзывы:

Бренды по названию

Популярные бренды

Emerson Easyheat GC-1, Руководство по обслуживанию

Результаты поиска

Содержание Easyheat GC-1

Отзывы:

Бренды по названию

Популярные бренды