Emerson Daniel PT Series Скачать руководство пользователя страница 3

Страница: 3 / 68

Signal words and symbols

Pay special attention to the following signal words, safety alert symbols and statements:

Safety alert symbol

This is a safety alert symbol. It is used to alert you to potential physical injury hazards. Obey all safety messages that follow this symbol
to avoid possible injury or death.

DANGER!

Danger indicates a hazardous situation which, if not avoided, will result in death or serious injury.

WARNING!

Warning indicates a hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION!

Caution indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

NOTICE

Notice is used to address safety messages or practices not related to personal injury.

Important

Important is a statement the user needs to know and consider.

Tip

Tip provides information or suggestions for improved efficiency or best results.

Note

Note is “general by-the-way” content not essential to the main flow of information.

Содержание Daniel PT Series





































































Результаты поиска

Содержание Daniel PT Series

Отзывы:

Похожие инструкции для Daniel PT Series

Бренды по названию

Популярные бренды

Emerson Daniel PT Series, Инструкция по установке и обслуживанию

Результаты поиска

Содержание Daniel PT Series

Отзывы:

Похожие инструкции для Daniel PT Series

Бренды по названию

Популярные бренды