manualshive.com logo in svg

Emerson COPELAND ZO18AG, Инструкции по применению

Поделиться
Скачать
Emerson COPELAND ZO18AG Скачать руководство пользователя страница 23

 

18 

 

AGL_Ref_ST_ZO_E_Rev00 

4 

Electrical connection 

4.1  General recommendations 

 

WARNING 
Electrical hazard!  Serious personal injuries and/or system breakdown!

 

The  compressor  must  always  have  the  ground  wire  attached  to  the 
compressor  terminal  fence.  The  other  end  of  the  ground  wire  must  be 
connected to the appropriate ground terminal on the drive. 
Disconnect and  lock out power  before servicing.  Allow drive components  to 
electrically  discharge  before  servicing.  Respect  the  time  according  to  drive 
manual  before  servicing  the  drive.  Use  compressor  with  grounded  system 
only. Refer to original equipment wiring diagrams. Electrical connections must 
be made by qualified electrical personnel. 

 

 

CAUTION 
High  voltage!  Drive  damage!

  An  optional  unit  contactor  must  be  installed 

upstream of the drive, not between the drive and the compressor. Nor should 
a  disconnected  switch  be  installed  between  the  drive  and  the  compressor. 
Major faults and irreversible damage to the drive could occur if the drive output 
is open-circuit while the compressor is running. 

 

Before connecting the drive to the power network, make sure that all the cables to and from the drive 
and to the compressor are correctly connected and that the supply voltage, phases and frequency 
match the drive nameplate data. 

Wiring should remain physically separated to minimize the introduction of electrical noise. 

Before connecting the compressor, ensure the supply voltage, the phases and the frequency match 
the nameplate data. 

For safety reasons, Emerson recommends that the electrical installation be executed in compliance 
with standard  EN 60335-1  and/or  other  standards  and  regulations  of  application.  The  wiring  must 
conform to local regulations and codes of practice. 

NOTE: The drive assembly contains accessories such as chokes and EMC filters, which are 
part  of  the  drive.  For  detailed  list  and  description  please  refer  to  the  EVM/EVH  Drive  User 
Manual. 

4.2  Electrical wiring 

 

WARNING 
Conductor  cables!  Electrical  shock!

  Shut  off  power  supply  before 

undertaking any task on electrical equipment. 

 

For recommended wiring diagrams, see Error! Reference source not found.. 

The combination of ZOV*AG compressors and inverters can cause earth leakage currents, both AC 
and DC, due to the presence of the inverter and an EMC filter in the system. Therefore an AC/DC-
sensitive residual current device (RCD) must be used on the power  supply side. The RCD can be 
either type B or B+. 

NOTE: For recommendations about the EMC and details about wiring up the drive assembly, 
please refer to the EVM/EVH User Manual. 

 

Содержание COPELAND ZO18AG







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды