background image

1. Check to see that you have received the following

parts:

NOTE: If you are uncertain of part description,
refer to exploded view illustration.

a. Fan motor assembly
b. One ceiling cover
c. Five fan blades
d. Five blade flanges
e. One hanger ball/downrod assembly
f. One hanger bracket
g. One glass globe
h. One SR100 fan/light control
i. One light kit plate
j. One adapter plate
k. One coupler cover
l. One loose parts bag containing:

1. Sixteen 3/16-24 x 5/16” slotted Phillips 

washer head blade screws

2. Sixteen Fiber blade washers
3. Eleven 1/4-20 x 3/8” Phillips oval head 

flange screws

4. Three wire connectors
5. Two 3/4" threaded studs
6. Two lockwashers
7. Two knurled knobs
8. One clevis pin
9. One hairpin clip

10. One 3/16” hex wrench
11. Three 3/16-24 nuts

This Manual Is Designed to Make it as Easy as Possible for You to

Assemble, Install, Operate and Maintain Your Ceiling Fan

Tools Needed for Assembly

One Phillips head screwdriver

One stepladder

One 1/4” blade screwdriver

One wire stripper

Three wire connectors (supplied)
One 3/16” hex wrench (supplied)

MATERIALS

Wiring outlet box and box connectors must be of type
required by the local code. The minimum wire would
be a 3-conductor (2-wire with ground) of the following
size:

3

Unpacking Instructions

For your convenience, check-off boxes are provided next to each step. As each step is
completed, place a check mark in the box. This will insure that all steps have been
completed and will be helpful in finding your place should you be interrupted.

NOTE: Place the parts from the loose parts bags
in a small container to keep them from being lost.
If any parts are missing, contact your local
retailer or catalog outlet for replacement before
proceeding.

2. Remove the fan assembly from the protective

plastic bag. Place the fan assembly into the upper
foam pad with the top of the motor facing up.

The upper foam pad serves as a holder for the fan
during the first stages of assembly.

BLADE
FLANGES

GLASS
BOWL

ADAPTER PLATE

FAN
ASSEMBLY

COUPLER
COVER

CEILING
COVER

FAN BLADES

LIGHT KIT
PLATE

HANGER
BRACKET

HANGER BALL/
DOWNROD 
ASSEMBLY

LOOSE
PARTS
BAG

SR100
FAN/LIGHT
CONTROL

H

I

OFF

LOW

MED

Installed Wire Length

Wire Size A.W.G.

Up to 50 ft.

14

50-100 ft.

12

Before assembly your ceiling fan, refer to section on
proper method of wiring your fan (page 6). If you feel
you do not have enough wiring knowledge or
experience, have your fan installed by a licensed
electrician.

WARNING

!

Do not install or use fan if any part is damaged or
missing. Call Toll-Free:

1-800-654-3545

This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product by
Emerson Company. Substitution of parts or
accessories not designated for use with this product
by Emerson Company could result in personal injury
or property damage.

WARNING

!

WARNING

!

Содержание COOLER CF925BK00









Отзывы: