Emerson CF370BQ00 Скачать руководство пользователя страница 22

Страница: 22 / 32

ETL Model No.: CF370

8. Wall Control Installation

(Continued)

FAN/LIGHT WALL

CONTROL

WALL

BOX

BLACK

BLK

HOT

NEUTRAL

WIRES

DECORATIVE WALL PLATE

SCREWS (2)

SWITCH COVER

TO 120VAC SOURCE

TO LOAD

OFF

....

OFF

....

Figure 34

Check to see that all connections are tight and that no

bare wires are visible at the wire connectors.

WARNING

Do not connect any neutral (white) wire to this control.

Incorrect wiring will damage this control.

WARNING

8.3

Before installing the Wall Control, place the Wall Control

in “OFF” mode by pushing “ON/OFF” Switch to the

“OFF” position.

8.4

Connect one Black Wire of the Wall Control to the

“HOT” Wire. Securely connect Wires with Wire

Connector, supplied (Figure 34).

8.5

Connect one Black Wire of Wall Control to the “LOAD”

(Black) Wire in Wall Box. Securely connect Wires with

Wire Connector, supplied.

8.6

Screw the Wall Control into Wall Box using the supplied

Screws. Leave the Wall Control in “OFF” mode until

Fan installation is completed.

8.7

The Wall Control is supplied with a White, Ivory, and

Almond color Switch Covers. Choose the finish that

best suits your needs and snap the Cover onto the Wall

Control (Figure 34).

8.8

Install Decorator Wall Plate using the two Screws

provided with Wall Plate. Leave the Wall Control in

“OFF” mode until Fan installation is completed

(Figure 34).

Содержание CF370BQ00

































Результаты поиска

Содержание CF370BQ00

Отзывы:

Похожие инструкции для CF370BQ00

Бренды по названию

Популярные бренды

Emerson CF370BQ00, Руководство пользователя

Результаты поиска

Содержание CF370BQ00

Отзывы:

Похожие инструкции для CF370BQ00

Бренды по названию

Популярные бренды