background image

Trouble Shooting

TROUBLE

PROBABLE CAUSE

SUGGESTED REMEDY

1. Fan will not start. 1. Fuse or circuit breaker blown.

1. Check main and branch circuit fuses or circuit breakers.

2. Loose power line connections to the fan, or loose 

2.

Check line power connections to fan and switch wire

switch wire connections in the switch housing.

connections in the switch housing.

WARNING: 

Make sure main power is turned off.

2. Fan sounds 

1. Blades not attached to fan.

1. Attach blades to fan before operating.

noisy.

2. Screws securing fan blade flanges to motor 

2. Check to make sure the screws which attach the fan flanges

are loose. 

to the motor are tight. 

3. Wire connectors inside switch housing rattling.

3. Check to make sure wire connectors in switch housing are 

not rattling against each other or against the interior wall of 
the switch housing.

WARNING: 

Make sure main power is turned off.

4. Screws holding blades to flanges are loose.

4. Tighten screws securely.

5. Loose screws in motor housing.

5. Check to make sure all screws in motor housing are snug

(not over-tight)

3. Fan wobbles

1. Setscrew in motor coupling is not tightened 

1. Raise coupling cover and tighten setscrew securely.

excessively.

securely.

2. Setscrew in the hanger ball/downrod assembly 

2. Tighten the setscrew in the hanger ball/downrod assembly.

is loose.

3. Screws securing fan blade flanges to 

3. Check to be sure screws which attach the fan blade flanges 

motor are loose.

to the motor are tight.

4. Fan blade flanges not seated properly.

4. Check to be sure the fan blade flanges seat firmly and 

uniformly to the surface of the motor. If flanges are seated 
incorrectly, loosen the flange screws and retighten
according to Step 17 and Figure 11.

5. Hanger bracket and/or ceiling outlet box is 

5. Tighten the hanger bracket screws to the outlet box, and/or 

not securely fastened

secure outlet box. 

6. Fan blades out of balance.

6. Interchanging an adjacent (side-by-side) blade pair can 

redistribute the weight and result in smoother operation. 
Or use supplied balancing kit to balance blades.

WARNING: 

FOR YOUR OWN SAFETY TURN OFF POWER AT FUSE BOX OR CIRCUIT BREAKER

BEFORE TROUBLE SHOOTING YOUR FAN.

!

!

!

10

Maintenance

IMPORTANT CARE INSTRUCTIONS

for your Ceiling Fan

Periodic cleaning of your new ceiling fan is the only
maintenance that is needed.

When cleaning, use only a soft brush or lint free cloth
to avoid scratching the finish.

Abrasive cleaning agents are not required and should
be avoided to prevent damage to finish.

Accessories

1. Downrod Extension Kits (see store or catalog).

2. Ceiling Fan Controls (see store or catalog).

Do not use water when cleaning your ceiling fan. It
could damage the motor or the blades and create the
possibility of an electrical shock.

WARNING

!

This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product by
Emerson Company. Substitution of parts or
accessories not designated for use with this product
by Emerson Company could result in personal injury
or property damage.

The use of any other control not specifically
approved for this fan could result in fire, shock and
personal injury.

WARNING

!

WARNING

!

Содержание CF2800BS













Отзывы: