background image

button is held down. When the light is
at the desired brightness, release the
button.

5. To turn the light on and off, press and

release the       button. The light will turn
on at the light level previously set (see
step 4).

6. If airflow is desired in the opposite

direction, turn the fan off and wait for
the blades to stop turning. Then slide
the reversing switch (Figure 18) to the
opposite position and turn the fan on
again. The blades will turn in the oppo-
site direction and reverse the airflow.

REVERSING 
SWITCH

9. Grasp the lower ring assembly and

raise it up and over the ring rods of the
adapter assemlby (Figure 16). Position
the ring assembly of that the ring
assembly arms protrude through the
holes at the end of the ring rods.
Secure the ring asembly in the ring
rods using the six ring screws.

10. Your ceiling fan is now installed and

wired to be controlled by your remote
control system.

11

LOWER RING 
ASSEMBLY

RING
SCREWS (6)

RING ROD

ARM

Figure 16

Operating Your

Ceiling Fan

IMPORTANT

Fan installation must be completed,
including the installation of the fan
blades, before testing of the remote
control.

Your remote control (Figure 17) has full
control of your fan and light. However, air-
flow direction is controlled by a slide
switch on the switch housing.

1. Restore electrical power to the outlet

box by turning the electricity on at the
service panel.

2. To set the desired fan speed, press the

HI, MED, or LOW buttons to operate
your fan on high, medium, or low speed
(Figure 17).

3. To turn your fan off, press the OFF

button.

4. To set the level of light brightness,

press and hold the light       button. The
light brightness will continue to
increase then decrease while the

STORAGE
BRACKET

H

I

OFF

LOW

MED

Figure 17

Figure 18

Installation of

Storage Bracket

A storage bracket is supplied with the
remote control for holding the transmitter
when not in use. If you desire to use the
bracket, use the two screws (supplied)
and install it on a wall that is away from
excess heat or humidity.

U.L. Model No.: CF180

BP7357 CF180 BRIDGETON  9/19/07  11:21 AM  Page 11

Содержание BRIDGETON CF180AP00

















Отзывы: