Emerson Bettis Electro-Hydraulic Operated Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 50

Emerson Bettis Electro-Hydraulic Operated Скачать руководство пользователя страница 44

Installation, Operation and Maintenance Manual

VCIOM-13254-EN Rev. 3

February 2021

40

Section 5: Operation

Operation

5.4.2.1 Accumulator Charge

The motor (Z) drives the hydraulic pump (Y) and discharges fluid to the nitrogen

blanket pre-charged accumulator (E).

5.4.2.2 Power Stroke ((Open/Close))

Upon completion of the accumulator charging, the pressure switch (R) set point is
reached and stops the motor. Either one of the two closing or opening solenoids (J)
or (K) are energized open and the accumulator (E) provides hydraulic pressure to

flow thru the energized solenoid, either (J) or (K) and the actuator strokes open

or closed.

5.4.2.3 ESD Operation ((Optional))

In an ESD application the ESD Solenoid (P) is constantly energized closed. This
customer supplied signal is held as long as the signal is present. Upon loss of the
signal to the ESD solenoid, the solenoid will de-energize and open allowing

hydraulic supply fluid from the accumulator (E) to pass thru the ESD solenoid and

to the closing port of the actuator (W).

5.4.2.4 Manual Handpump Stroke

1. Open the Handpump Selection Isolation Valve (M) to the pump position.

NOTE:

Both Handpump Selection Isolation Valves (M) must be engaged whether hand pumping
open or close.

2. Select and push the open or close knob on the Handpump (L).

3. Stroke the handpump until the OPEN/CLOSE stroke is completed.

4. Push the manual relief valve located on the handpump to retract the pump

ram back into the pump body and pull the pump handle down.

5. Upon completion of the OPEN/CLOSE handpump stroke, return both

handpump selection isolation valves back to the automatic position.

5.4.2.5 Accumulator override Feature ((Optional))

To stroke the actuator OPEN or CLOSED using the accumulator override isolation
valves , open valve (AD) to stroke the actuator open, or open (AE) to stroke the
actuator closed.

«
...
42
43
44
45
46
...
»

Содержание Bettis Electro-Hydraulic Operated



















































Отзывы:

Нет отзывов