Emerson Bettis Electro-Hydraulic Operated Скачать руководство пользователя страница 42

Страница: 42 / 50

Installation, Operation and Maintenance Manual

VCIOM-13254-EN Rev. 3

February 2021

Section 5: Operation

Operation

Hydraulic Pressure Gauge

(R)

Pressure Switch

(L)

Handpump: Used to manually stroke the actuator open or closed.

(AD) Optional accumulator override 3-way isolation valve to open the actuator.

(AE) Optional accumulator override 3-way isolation valve to close the actuator.

(M) Handpump Selection Valves: These two valves are engaged to isolate the control

system before using the handpump. Note: Both selection valves are engaged at

the same time when the handpump is used to open or close the actuator.

(X)

Shuttle Valve; (Optional) Used with an optional pressure transmitter.

(P)

(Optional) ESD 3-Way Normally Open Solenoid Valve.

(E)

(Optional) Hydraulic Accumulator w/nitrogen blanket charge:

The accumulator is used to stroke the actuator open or close with an additional

override feature.

(B)

(Optional) Nitrogen Relief Valve: The relief valve is provided to prevent the

nitrogen gas pressure to reach an over pressurization point caused by the pump

or excessive thermal expansion.

(N) (Optional) Accumulator Isolation Valve: Used to isolate the accumulator for repair

or maintenance.

(AB) (Optional) Pressure Transmitter: Used to transmit the pressure required to stroke

the valve over time as a diagnostic feature.

(H) (Optional) Accumulator Isolation Valve: This valve allows the hydraulic pressure to

bypass back to the reservoir.

(D) (Optional) Isolation Valve: Used to blow down or decay the nitrogen pressure from

the accumulator for repair or maintenance.

(A)

(Optional) Pressure Gauge: Illustrates the accumulator nitrogen blanket pressure.

(O) (Optional) Handpump Isolation Valve: This valve isolates the ESD solenoid and

must be closed prior to using the handpump for stroking the actuator open or closed.

(AC) (Optional) Shuttle Valve: This valve allows the actuator to close by either remote

electric by energizing the closing solenoid item (K) or by losing the electric signal

thru the ESD solenoid item (P).

(S)

(Optional) Pressure Transmitter: Used to transmit the accumulator nitrogen

blanket pressure.

Содержание Bettis Electro-Hydraulic Operated



















































Результаты поиска

Содержание Bettis Electro-Hydraulic Operated

Отзывы:

Emerson Bettis Electro-Hydraulic Operated, Инструкция по установке, эксплуатации и обслуживанию, Страница: 42 / 50

Результаты поиска

Содержание Bettis Electro-Hydraulic Operated

Отзывы: