background image

9

2.

Carefully lift the fan and seat the
hanger ball/downrod assembly on the
hanger bracket that was just attached
to the outlet box (Figure 12). Be sure
the groove in the ball is lined up with
the tab on the hanger bracket
(Figure 11).

Hanger bracket must seat firmly against
outlet box. If the outlet box is recessed,
remove wall board until bracket contacts
box. If bracket and/or outlet box are not
securely attached, the fan could wobble
or fall.

!

WARNING

Failure to seat tab in groove could cause
damage to electrical wires and possible
shock or fire hazard.

!

WARNING

To avoid possible fire or shock, do not
pinch wires between the hanger
ball/downrod assembly and hanger
bracket.

!

WARNING

TWO SCREWS
SUPPLIED
WITH
OUTLET BOX

HANGER
BRACKET

TAB

OUTLET
BOX

NOTE: CEILING COVER, SUPPLY WIRES AND FAN 
WIRES OMITTED FOR CLARITY.

OUTLET
BOX

HANGER
BRACKET

HANGER BALL/
DOWNROD
ASSEMBLY

Figure 11

Figure 12

1.

Position the supply wires to the left side
of the outlet box (Figure 13); position
the fan wires to the right side. Partially
insert the remote control receiver (flat
side up) until one end rests on the
hanger ball as shown in Figure 13.

NOTE: Make all wiring connections
using wire connectors (supplied). Make
sure that all connections are tight,
including ground, and that no bare wire
is visible at the wire connectors, except
for the ground wire.
2.

Refer to Figures 13 and 14 and connect
the receiver wires to the supply wires
and the fan motor wires as follows:

a.

Securely connect the green grounding
wires from the hanger ball and the
hanger bracket to the supply grounding
conductor (this may be a bare wire or a
wire with green insulation).

b.

Securely connect the supply white
(neutral) wire to the receiver white
(AC IN N) wire.

c.

Securely connect the supply black wire
(hot) wire to the receiver black (AC IN
L) wire.

d.

Securely connect the fan motor white
wire to the receiver white (TO MOTOR
N) wire.

How to Wire

Your Ceiling Fan

Turning off wall switch is not sufficient.
To avoid possible electrical shock, be
sure electricity is turned off at the main
fuse box before wiring. All wiring must be
in accordance with National and Local
codes and the ceiling fan must be
properly grounded as a precaution
against possible electrical shock.

!

WARNING

If you feel that you do not have enough
electrical wiring knowledge or
experience, have your fan installed by a
licensed electrician. 

CAUTION: To reduce the risk of
electrical shock, disconnect the
electrical supply circuit before
installing the fan, light kit or receiver.

Содержание ATOMICAL CF930BS01





















Отзывы: