Emec TMS DC Series Скачать руководство пользователя

Страница: 6 / 44

Pump’s installation and operativity is made in 4 main steps:

Pump’s installation

Hydraulic Installation (hoses, level probe, injection valve)

Electrical Installation (main power connection, priming)

Programming the pump.

Before to start, please read carefully the following safety information.

Protective clothes

Wear always protective clothes as masks, gloves, safety glasses and

further security devices during ALL installation procedure and while

handling chemicals.

Installation location

Pump must be installed in a safety place and fixed to the table / wall to

avoid vibration problems!

Pump must be installed in a easy accessible place!

Pump must be installed in vertical position!

Avoid water splashes and direct sun!

Hoses and Valves

Suction and delivery hoses must be installed in vertical position!

All hoses connections must be performed using only hands’ force!

No tongs required!

Delivery hose must be firmly fixed to avoid suddenly movements

that could damage near objects!

Suction hose must be shorter as possible and installed in vertical

position to avoid air bubbles suction!

Use only hoses compatibles with product to dose! See chemical

compatibility table. If dosing product is not listed please

consult full compatibility table or contact chemical’s manufacturer!

4. Before to Install warnings

Feeder should be interlocked with a no-flow protection device to automatically shut-off the

pumps when there is no flow!

Adequate measures shall be taken to prevent cross connection of chemicals!

Chemical feeding must be stopped during backwash cycles and periods of noflow as these con-

ditions may introduce the potential for chemical overdosing. Not doing so may result in elevated

chemical concentrations and hazerdous gas introduction into the pool or spa.

Содержание TMS DC Series













































Результаты поиска

Содержание TMS DC Series

Отзывы:

Похожие инструкции для TMS DC Series

Бренды по названию

Популярные бренды

Emec TMS DC Series, Руководство по эксплуатации

Результаты поиска

Содержание TMS DC Series

Отзывы:

Похожие инструкции для TMS DC Series

Бренды по названию

Популярные бренды