Embraco Fullmotion CF10C Скачать руководство пользователя страница 5

Страница: 5 / 48

GENERAL PRECAUTIONS

WARNING

NOTICE

CAUTION

• During instalation the environment must be prop-

erly protected against ESD. The operator and ma-
chines must be properly Earthed.

• Make sure that Fullmotion CF10C Inverter will not

be in direct contact with flames during assembly.

• The location where the Inverter will be installed

must be protected against splashed water from all
directions.

• Do not open the Inverter enclosure. For installa-

tion, remove only the Inverter Cover to make the
electrical connections.

WARNING

NOTICE

CAUTION

• This inverter is for use only with the Fullmotion Em-

braco compressors.

• Read this material carefully before you begin the

Fullmotion CF10C Inverter installation and start up
procedure.

• To prevent damage to your inverter during and af-

ter assembly, avoid contacting with the following
substances: Hydrocarbons; Ester based oils (e.g.:
compressor oil); Phenols; Amines; Ketenes; Au-
tomotive fluids such as grease, except glycol and
heavy alcohol.

WARNING

NOTICE

CAUTION

• The protection against access to live parts have

been evaluated according to the relevant require-
ments from IEC 60335-1 and UL 60730-1.

Содержание Fullmotion CF10C

















































Результаты поиска

Содержание Fullmotion CF10C

Отзывы:

Похожие инструкции для Fullmotion CF10C

Бренды по названию

Популярные бренды

Embraco Fullmotion CF10C, Руководство по эксплуатации продукта

Результаты поиска

Содержание Fullmotion CF10C

Отзывы:

Похожие инструкции для Fullmotion CF10C

Бренды по названию

Популярные бренды