Elvox 52D0/EIR, Инструкция по установке и эксплуатации, Страница: 45 / 64

45
Y - M - D 07 - 01 - 18
H - M - S 15 - 33 - 25
DONE OPEN
QUIT OPEN
- ZERO ANGLE (North Direction):
Enter the ZERO ANGLE (azimuth/elevation) menu and then use the joystick of keyboard or the direction buttons on DVR front
panel to define the amount of pan from zero degrees vertical and the amount of tilt from zero degrees horizontal, and finally press
the Iris+ button to save settings and exit the current menu.
- DISPLAY SETTINGS
The DISPLAY SETTINGS menu is displayed in two pages, as shown in Figure 3.3.6 and Figure 3.3.7.
Each item can be set with the separate display time on screen from 2sec, 5sec and 10 sec selectable, or set to be ON or OFF.
The preset display position can overlapped the display positions of azimuth/elevation and zoom. If both of the ZOOM SHOW
and the PT SHOW are set to ON, then in the preset operation status, the preset label will be displayed all the time; while in other
operation status, the azimuth/elevation and zoom label are displayed all the time in other status. The external alarm response
actions can be activated in non-menu programming mode while disabled in the menu programming mode.
DISPLAY SETTINGS
ZOOM SHOW 2
PT SHOW 2
ALARM SHOW ON
TIME SHOW ON
PRESET SHOW ON
ZONE SHOW ON
BACK EXIT
DISPLAY SETTINGS
ADDRESS SHOW OFF
ERROR RATE SHOW OFF
BACK EXIT
Figure 3.3.6 Figure 3.3.7
Figure 3.3.6
- LED PARAMETERS
The IR SENSITIVITY refers to the value of the infrared lamp, with HIGH, MEDIUM and LOW levels selectable. The N/M LED
CURRENT indicates the strength of the near/medium-distance infrared lamp, with HIGH, MEDIUM and LOW levels selectable;
the FAR LED CURRENT indicates the strength of the far infrared lamp; the REFERENCE HEIGHT refers to the height from the
dome installed to the ground, with 1m to 10m selectable, and this option can also be used for realizing the switch between the
far infrared lamp and N/M infrared lamp; the REFERENCE ZOOM can be set from 2X to 10X, when the camera zoom is set to
be larger than the selected reference zoom, please turn on the far infrared lamp, otherwise, turn on the near/medium infrared
lamp; the LED CONTROL can be set to FAR ON, M/F ON, DIST FIRST, ZOOM FIRST and CLOSE options according to different
requirements; and the FAN CONTROL is used for controlling the LED fan, which can be set to ON, OFF or TEM.
- SOFT BAUD RATE
When the SOFT BAUD option from the menu is set to ON, the speed dome will use the soft baud rate, as shown in Figure 3.3.3,
with 2400, 4800, 9600 and 19200 selectable. In this status, it is invalid to set baud rate by DIP switch. When the SOFT BAUD
option is set to OFF, the baud rate can be set by DIP switch.
Note: when the soft baud rate function has been enabled and configured, the dome will reboot to activate the settings; and when
the soft baud rate function is disabled, the dome will reboot as well.
- BROADCAST ADDRESS
When the BROADCAST ADDRESS is set to ON, the control device with address 0 is capable of controlling all domes connec-
ted to it.
- PELCO CHECKSUM
When the dome in PELCO-P and PELCO-D protocol cannot be controlled, user may enable this function to solve the problem.
- SYSTEM TIME
The SYS TIME allows user to set the date and time of the dome. As shown in Figure 3.3.5, the message indicates the current
date and time is 15:33:25 on January 18th , 2007.
Move the joystick of the keyboard or use the Left and Right buttons on DVR front panel to select the option, and move the joy-
stick of the keyboard or use the Up and Down buttons to modify the value.
GB