Eltroplan REVCON DC 13-400-1-0 Скачать руководство пользователя страница 45

Страница: 45 / 77

Electrical Installation

Operating instructions DC(S)

ELTROPLAN

REVCON



Elektrotechnische Anlagen GmbH

4.3

Electrical installation

4.3.1

Operator’s safety

Danger!

After mains disconnection, the DC-bus terminals of the power feed/feedback unit remain live for

several minutes! The exact time, till this voltage has decreased to a not dangerous value is de-

pendant on the used controller and has to run down before any service operations or similar ac-

tivities are started.

The exact values have to be cross checked with the documentation of the controller.

Replace defective fuses by the regular types (chapter 3.3.5) only and without any live volt-

age.

4.3.2

Protection of the power feed/feedback unit

Stop!

The power feed/feedback units contain electrostatic sensitive devices (ESSD).

During working at the terminals the personnel has to observe the rules of the international stan-

dard IEC 747-1 chapter 9. Basically before starting the works the personnel has to free itself

from electrostatic voltages:

Discharge yourself by touching the PE-screw of the housing or another grounded surface in the

cabinet.

STOP

Содержание REVCON DC 13-400-1-0














































































Результаты поиска

Содержание REVCON DC 13-400-1-0

Отзывы:

Похожие инструкции для REVCON DC 13-400-1-0

Бренды по названию

Популярные бренды

Eltroplan REVCON DC 13-400-1-0, Руководство по эксплуатации

Результаты поиска

Содержание REVCON DC 13-400-1-0

Отзывы:

Похожие инструкции для REVCON DC 13-400-1-0

Бренды по названию

Популярные бренды