Eltroplan REVCON DC 13-400-1-0 Скачать руководство пользователя страница 52

Страница: 52 / 77

Electrical Installation

Operating instructions DC(S)

ELTROPLAN

REVCON



Elektrotechnische Anlagen GmbH

Legend for figure 4.4.1.1.1 (REVCON



DC(S))

Fusing in accordance with this manual.

It is not allowed to connect any other devices except the frequency inverter and the

power feed/feedback unit behind the main magnetic switch.

Danger!

If this is not observed, you take the risk that, in the case of switching off the mains during feed

back the power, the voltage in that sector may rise up to a dangerous level. This may destroy

the connected devices and perhaps also the inverter and/or the power feed/feedback unit. To

avoid such situation, the power feed/feedback unit is equipped with an overvoltage switch off,

but nevertheless this hint should be observed!

Option RFI filter

Separate fusing in accordance with DIN VDE 0298 or short circuit proof wiring.

commutation choke in accordance with this manual

It is absolutely necessary to install the inrush current limit circuit of the controller be-

tween the DC-output to the REVCON and the DC-bus capacitors.

At these terminals one ore more controllers (even with different power ratings) may

be attached, like it shown in figure

4.5.1. Even if several controllers are attached, the

wires have to be as

short and low impedance

as possible!

The „ON“ or „RESET“ signal may be initiated via terminals 11 and 12:

Terminals 11 and 12:

Positive pulse (12-24 V DC); practicable e.g. via PLC

(terminal 11 +, terminal 12 -).

Содержание REVCON DC 13-400-1-0














































































Результаты поиска

Содержание REVCON DC 13-400-1-0

Отзывы:

Похожие инструкции для REVCON DC 13-400-1-0

Бренды по названию

Популярные бренды

Eltroplan REVCON DC 13-400-1-0, Руководство по эксплуатации

Результаты поиска

Содержание REVCON DC 13-400-1-0

Отзывы:

Похожие инструкции для REVCON DC 13-400-1-0

Бренды по названию

Популярные бренды