manualshive.com logo in svg

eltherm ELTC-MV2, Руководство по эксплуатации, Страница: 25 / 28

Поделиться
Скачать
eltherm ELTC-MV2 Скачать руководство пользователя страница 25

25 

www.eltherm.com

25 

www.eltherm.com

Sliding setpoint PWM

The actual value x

1

 is recorded via a temperature sensor or a 

standard signal and converted into a digital signal. Before this 
signal is sent to the controller, the actual value is corrected. 
The corrected actual value is shown on the display (P01).
The actual value x

2

 is recorded via a temperature sensor or a 

standard signal and converted into a digital signal. Before this 
signal is sent to the controller, the actual value is corrected. 
The corrected actual value is shown on the display (P02).
The temperature deviation w

2

 is set on the controller and is 

used to calculate the sliding setpoint w1. 
The sliding setpoint w

1

 = x

2

 + w

2

 , is calculated in the control-

ler and shown on the display.
A hysteresis h can be set on the controller and specifies the 
range in which the controller clocks.
The control difference  x

d

 = w

1

 - x

1

 is formed in the controller. 

Parameters used

No. description

factory 

setting

Own 
setting

P12 min. standstill time K1

0

P15 Sensor correction 1

0

P16

Over temperature alarm 1

999

P17 Low temperature alarm 1

-99

P18 Lower analog scaling value 

(0/2V, 0/4mA)

0

P19 Upper analog scaling value

 

(10V, 20mA)

100

P20 Control setpoint

 2 (= W2)

5

P23

Largest settable setpoint 2

950

P24

Smallest settable setpoint 2

-50

P25 Sensor correction

 2

0

P26

Over temperature alarm 2

999

P27 Low temperature alarm

 2

-99

P28

Power monitoring 
load output

0

P75

Low level mode analog inputs/
outputs

0

Hybrid relay K1 (PWM)

If the control difference is  x

d

 ≤ h, the hybrid relay clocks.

If the control difference is  x

d

 > h, he hybrid relay remains 

permanently closed.
If the control difference is  x

d

 < 0, the hybrid relay remains 

open.

ontrol of an external SSR relay (PWM)

The external SSR relay is switched via a voltage signal from the 
controller.

If the control difference is  x

d

 < 0, a signal with 0/2V is sent to 

the output and the SSR relay switches off.
If the control difference is  x

d

 ≥ 0, a 10V signal is sent to the 

output and the SSR relay switches on.

Control of an external power contactor (PWM)

If the control difference is x

d

 ≤ h, the safety relay clocks.

If the control difference is  x

d

 > h, the safety relay remains 

permanently closed.
If the control difference is x

d

 < 0, the safety relay remains open.

Structure switch settings

No. description

selection option

S01

Selection actual 
value 1 (X1)

[1] = Pt100, 3-wire (AE1) 
2 = Pt100, 2-wire (AE1) 
3 = thermocouple type J (AE1)  
4 = thermocouple type K (AE1)  
5 = voltage input (AE3) 
6 = current input (AE3)

S02

Selection actual 
value 2 (X2)

[1] = Pt100, 3-wire (AE2) 
2 = Pt100, 2-wire (AE2) 
3 = thermocouple type J (AE2)  
4 = thermocouple type K (AE2)  
5 = voltage input (AE4) 
6 = current input (AE4)

S03 Select setpoint W

4 = Sliding setpoint (W2+X2)

S04

Selection of output 
function controller

2 = PWM

S05

Selection switching 
output

[1] = internal hybrid relay with 
soft start 
2 = external power contactor 
3 = analog output clocked

Parameters used

No. description

factory 

setting

Own 
setting

P01 Input variable

 1 (X1)

Display only

P02 Input variable

 2 (X2)

Display only

P03 Reference variable W

Display only

P04 Current display

Display only

P11 Switching hysteresis 1

2

Содержание ELTC-MV2





























Отзывы:

Нет отзывов