Eltek GenII RC250 Скачать руководство пользователя страница 8

Страница: 8 / 46

3.8

Top panel connections

12V DC

regulated

comms

12VDC

(inner is -ve)

Comms

(6 way mini Din)

3.9

Specification

Maximum no. Channels 160
AC supply

100 to 250V AC (Use only Eltek power supply type

MP12U)

DC input

12VDC Maximum current <150mA

Battery endurance

Up to 72 hours

Battery charge time

Trickle - allow 72 hours to fully charge an

exhausted battery.

Controls

Concealed button (power off)

Freq. UHF (Europe)

Default is 434.225Mhz (the label on the base will
give the exact frequency)

Rx sensitivity

-117dbm (typical)

Antenna connection

SMA socket

Antenna

–

standard

type (supplied)

¼ wave whip (shipped with product)

–

Eltek

UHFFlexi/SMA

Antenna

–

lightweight

dipole (optional)

Indoor/outdoor dipole, lead length 5m standard

accessory type LW-ANT/SMA. The maximum

recommended lead length is 10m.

Antenna

–

compact

Yagi (optional)

Lightweight 3 element Yagi, providing up to 6db

gain supplied with 5m lead and plug.

Temperature Range

-10 to +55ºC

Humidity

95% non condensing

Environment

Indoor use only IP40. A secondary enclosure must

be used for outdoor use

Transmitter types

All in GenII range from serial number 7000

Transmitter Interval

1 second to 4 hours

Содержание GenII RC250















































Результаты поиска

Содержание GenII RC250

Отзывы:

Бренды по названию

Популярные бренды

Eltek GenII RC250, Руководство по эксплуатации

Результаты поиска

Содержание GenII RC250

Отзывы:

Бренды по названию

Популярные бренды