elsner elektronik Mini-Sewi KNX L-Pr Скачать руководство пользователя

Страница: 44 / 68

Parameter setting

Sensors Mini-Sewi KNX TH-L-Pr and Mini-Sewi KNX L-Pr

• Version: 30.08.2018 • Technical changes and errors excepted.

If setpoint values are entered separately:

If the comfort setpoint value is used as a basis:

If the comfort setpoint value is used as a basis, the reduction/increment of the value is
set.

If the comfort setpoint is used as the basis without a switching object, a dead zone is
specified for the control mode "heating

and

cooling" to avoid direct switching from he-

ating to cooling.

Standby setpoint

Standby mode is usually used for daytime mode when people are absent.

If setpoint values are entered separately:

A starting setpoint value is defined as well as a temperature range in which the setpoint
value may be changed.

If the comfort setpoint value is used as a basis:

If the comfort setpoint value is used as a basis, the reduction/increment of the value is
set.

Eco setpoint

Eco mode is usually used for night mode.

Min. object value heating/cooling
(in 0.1 °C)

-300…800; 160

Max. object value heating/cooling
(in 0.1 °C)

-300…800; 280

Minimum base setpoint (in 0.1°C)

-300…800; 160

Maximum base setpoint (in 0.1°C)

-300…800; 280

Reduction by up to (in 0.1°C)

0…100; 50

Increase by up to (in 0.1°C)

0…100; 50

Dead zone between heating and cooling

(only if both heating AND cooling are used)

1…100; 50

Starting heating/cooling setpoint (in 0.1 °C)
valid until 1st communication

-300…800; 180

Min. object value heating/cooling
(in 0.1 °C)

-300…800; 160

Max. object value heating/cooling
(in 0.1 °C)

-300…800; 280

Reduce heating setpoint (in 0.1°C)

(for heating)

0…200; 30

Increase cooling setpoint (in 0.1°C)

(for cooling)

0…200; 30

Содержание Mini-Sewi KNX L-Pr





































































Результаты поиска

Содержание Mini-Sewi KNX L-Pr

Отзывы:

Похожие инструкции для Mini-Sewi KNX L-Pr

Бренды по названию

Популярные бренды

elsner elektronik Mini-Sewi KNX L-Pr, Инструкция по установке и настройке

Результаты поиска

Содержание Mini-Sewi KNX L-Pr

Отзывы:

Похожие инструкции для Mini-Sewi KNX L-Pr

Бренды по названию

Популярные бренды